ttyadm(1M)						  System Administration Commands						ttyadm(1M)

NAME

       ttyadm - format and output port monitor-specific information

SYNOPSIS

       /usr/sbin/ttyadm  [-b] [-c] [-h] [-I] [-r count] [-i msg] [-m modules] [-p prompt] [-t timeout] [-S y | n]  [-T termtype] -d device -l tty-
       label -s service

       /usr/sbin/ttyadm -V

DESCRIPTION

       The ttyadm command is an administrative command that formats ttymon(1M)-specific information and writes it to standard output. The  Service
       Access  Facility  (SAF)	requires each port monitor to provide such a command. Note that the port monitor administrative file is updated by
       the Service Access Controller's administrative commands, sacadm(1M) and pmadm(1M). ttyadm provides a means  of  presenting  formatted  port
       monitor-specific (ttymon-specific) data to these commands.

OPTIONS

       The following options are supported:

       -b	       Set  the  ``bi-directional  port''  flag. When this flag is set, the line can be used in both directions. ttymon will allow
		       users to connect to the service associated with the port, but if the port is free, uucico(1M), cu(1C), or ct(1C) can use it
		       for dialing out.

       -c	       Set the connect-on-carrier flag for the port. If the -c flag is set, ttymon will invoke the port's associated service imme-
		       diately when a connect indication is received (that is, no prompt is printed and no baud-rate searching is done).

       -d device       device is the full pathname of the device file for the TTY port.

       -h	       Set the hangup flag for the port. If the -h flag is not set, ttymon will force a hangup on the line by setting the speed to
		       0 before setting the speed to the default or specified value.

       -i message      Specify	the inactive (disabled) response message. This message will be sent to the TTY port if the port is disabled or the
		       ttymon monitoring the port is disabled.

       -I	       Initialize only.  If the -I option is used, ttymon will invoke the service only once.  This can be used to configure a par-
		       ticular device without actually monitoring it, as with software carrier.

       -l ttylabel     Specify which ttylabel in the /etc/ttydefs file to use as the starting point when searching for the proper baud rate.

       -m modules      Specify	a list of pushable STREAMS modules. The modules will be pushed in the order in which they are specified before the
		       service is invoked. modules must be a comma-separated list of modules, with no white space included. Any modules  currently
		       on the stream will be popped before these  modules are pushed.

       -p prompt       Specify the prompt message, for example, ``login:''.

       -r count        When  the -r option is invoked, ttymon will wait until it receives data from the port before it displays a prompt. If count
		       is 0, ttymon will wait until it receives any character. If count is greater than 0, ttymon will wait until  count  newlines
		       have been received.

       -s service      service is the full pathname of the service to be invoked when a connection request is received. If arguments are required,
		       the command and its arguments must be enclosed in double quotes (" ").

       -S y|n	       Set the software carrier value.	y will turn software carrier on. n will turn software carrier off.

       -t timeout      Specify that ttymon should close a port if the open on the port succeeds, and no input data is received in timeout seconds.

       -T termtype     Set the terminal type.  The TERM environment variable will be set to termtype.

       -V	       Display the version number of the current /usr/lib/saf/ttymon command.

OUTPUT

       If successful, ttyadm will generate the requested information, write it to  standard output, and exit with a status  of	0.  If	ttyadm	is
       invoked with an invalid number of arguments or invalid arguments, or if an incomplete option is specified, an error message will be written
       to standard error and ttymon will exit with a non-zero status.

FILES

       /etc/ttydefs

ATTRIBUTES

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWcsu			   |
       +-----------------------------+-----------------------------+

SEE ALSO

       ct(1C), cu(1C), pmadm(1M), sacadm(1M), ttymon(1M), uucico(1M), attributes(5)

       System Administration Guide: Basic Administration

SunOS 5.10							    14 Sep 1992 							ttyadm(1M)