Sponsored Content
Top Forums UNIX for Beginners Questions & Answers How to create a Solaris local zone with an exclusive NIC? Post 303041430 by Peasant on Saturday 23rd of November 2019 12:25:19 PM
Old 11-23-2019
Solaris 10 in LDOM should work fine from flar archive.
ldmp2v -
Oracle(R) VM Server for SPARC 3.5 Reference Manual


If something does not work you can always poweroff and delete ldom to reclaim resources.

Do not mix both on same box ....

Regards
Peasant.
 

9 More Discussions You Might Find Interesting

1. Solaris

Not able to ping global zone from local zone

Hi Gurus I am not able to ping the local zone from global zone when i am trying to ping i am getting below ICMP Host Unreachable from gateway zone ( 192.268.35.210) for icmp from zone ( 192.168.35.210) to sun1 ( 192.168.35.210) However i can ping local zone from global please... (12 Replies)
Discussion started by: kumarmani
12 Replies

2. Solaris

[Solaris 10]Zones and exclusive ip

Hello, I have a V120 server with two network interfaces. I would like to use one of them in my non global zone. I set the "ip-type=exclusive" as described here Solaris 10 8/07: Exclusive-IP Non-Global Zones (System Administration Guide: Solaris Containers-Resource Management and Solaris Zones) -... (2 Replies)
Discussion started by: Tex-Twil
2 Replies

3. Solaris

Global zone name from local zone

How to check the global zone name from local zone. (6 Replies)
Discussion started by: fugitive
6 Replies

4. Solaris

Covert Global zone to local zone

Dears, I would like to convert solaris 10 x86 and solaris 10 sparc (Global Zones) physical servers into Local zones. i found a document which seems to be helpful but i'm stuck @ the 1st step. to test this i want to do it 1st on x86 system running under vmware ESXi and if it succeeds i will... (1 Reply)
Discussion started by: mduweik
1 Replies

5. Solaris

create Virtual NIC in Solaris 10

Hi All, does any body know how to create Virtual NIC in Solaris 10 if any one have good article or reference kindly provide me i try to Google but i didn't find good one (7 Replies)
Discussion started by: jamisux
7 Replies

6. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

7. Solaris

Solaris 10 local zone on Solaris 11 global zone

Hi, A quick question: Can Solaris 10 local zones be moved to a Solaris 11 global zone and work well? Thank you in advance! (5 Replies)
Discussion started by: aixlover
5 Replies

8. Solaris

Solaris zone with full working NIC

I want a solaris zone,wich can get ip from dhcp external server i configure my zone net: address not specified allowed-address not specified configure-allowed-address: true physical: vnic1 defrouter not specified vnic is linked to net0 dladm net0 ... (6 Replies)
Discussion started by: Linusolaradm1
6 Replies

9. Solaris

Default route issue in share local zone in Solaris 11

Hi We took the reboot of server/global zone after that Solaris 11 share local zone not able to ping the default gateway but global zone able to ping same default gateway. I check/compare the before activity logs of global zone and local zones which looks fine to me, further IP and netmask of... (6 Replies)
Discussion started by: sb200
6 Replies
SVNPATH(1)                                                                                                                              SVNPATH(1)

NAME
svnpath - output svn url with support for tags and branches SYNOPSIS
svnpath svnpath tags svnpath branches svnpath trunk DESCRIPTION
svnpath is intended to be run in a Subversion working copy. In its simplest usage, svnpath with no parameters outputs the svn url for the repository associated with the working copy. If a parameter is given, svnpath attempts to instead output the url that would be used for the tags, branches, or trunk. This will only work if it's run in the top-level directory that is subject to tagging or branching. For example, if you want to tag what's checked into Subversion as version 1.0, you could use a command like this: svn cp $(svnpath) $(svnpath tags)/1.0 That's much easier than using svn info to look up the repository url and manually modifying it to derive the url to use for the tag, and typing in something like this: svn cp svn+ssh://my.server.example/svn/project/trunk svn+ssh://my.server.example/svn/project/tags/1.0 svnpath uses a simple heuristic to convert between the trunk, tags, and branches paths. It replaces the first occurrence of trunk, tags, or branches with the name of what you're looking for. This will work ok for most typical Subversion repository layouts. If you have an atypical layout and it does not work, you can add a ~/.svnpath file. This file is perl code, which can modify the path in $url. For example, the author uses this file: #!/usr/bin/perl # svnpath personal override file # For d-i I sometimes work from a full d-i tree branch. Remove that from # the path to get regular tags or branches directories. $url=~s!d-i/(rc|beta)[0-9]+/!!; $url=~s!d-i/sarge/!!; 1 LICENSE
GPL version 2 or later AUTHOR
Joey Hess <joey@kitenet.net> Debian Utilities 2013-12-23 SVNPATH(1)
All times are GMT -4. The time now is 10:07 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy