Looks like you are mixing ldoms and zones on the same box ?
This is doable, but ill advised.
Unfortunately I did not know that when I started. Yes, I have Solaris 11.4 installed on the T4-1 bare metal. Under the 11.4 global zone I have an LDOM running Linux for SPARC. That's working properly. Then I created a local zone under the global zone to run my Solaris 10 image. That zone is not running in the LDOM, it's side-by-side with it. I'd rather keep it this way than having to create another LDOM which would eat up more host memory and more CPU's, unless it just won't work at all. In any case, I finally got the zone to boot by saying this:
Code:
root@hemlock:/rpool# zoneadm -z s10zone attach -F
root@hemlock:/rpool# zoneadm -z s10zone boot
root@hemlock:/rpool# dladm
LINK CLASS MTU STATE OVER
ldoms-vsw0.vport0 vnic 1500 up net0
ldoms-vsw0.vport1 vnic 1500 up net0
net0 phys 1500 up --
net2 phys 1500 unknown --
net3 phys 1500 unknown --
net4 phys 1500 up --
sp-phys0 phys 1500 up --
s10zone/net0 vnic 1500 up net0
net1 phys 1500 unknown --
s10zone/net1 phys 1500 unknown --
root@hemlock:/rpool#
Notice that now how the listing has changed. net1 is listed last and there's two entires for s10zone. However, when the zone boots, it tries to connect to bge0 which was the NIC on the M3000 where this image was created. Of course it can't find it so it goes into maintenance mode immediately.
Code:
[NOTICE: Zone booting up]
SunOS Release 5.10 Version Generic_Virtual 64-bit
Copyright (c) 1983, 2013, Oracle and/or its affiliates. All rights reserved.
Failed to plumb IPv4 interface(s): bge0
Failed to plumb IPv6 interface(s): bge0
Failed to configure IPv4 DHCP interface(s): bge0
Moving addresses from missing IPv4 interface(s): bge0 (not moved -- not in an IPMP group).
Moving addresses from missing IPv6 interface(s): bge0 (not moved -- not in an IPMP group).
Nov 22 17:53:54 svc.startd[1221]: svc:/network/physical:default: Method "/lib/svc/method/net-physical" failed with exit status 96.
Nov 22 17:53:54 svc.startd[1221]: network/physical:default misconfigured: transitioned to maintenance (see 'svcs -xv' for details)
/usr/sbin/pmconfig: di_init init/access error
Hostname: s10zone
/usr/sbin/pmconfig: cannot open "/dev/pm": No such file or directory
Nov 22 17:53:55 svc.startd[1221]: svc:/platform/sun4u/dcs:default: Method "/lib/svc/method/svc-dcs" failed with exit status 96.
Nov 22 17:53:55 svc.startd[1221]: platform/sun4u/dcs:default misconfigured: transitioned to maintenance (see 'svcs -xv' for details)
Nov 22 17:53:56 svc.startd[1221]: svc:/system/sysevent:default: Method "/lib/svc/method/svc-syseventd start" failed with exit status 95.
Nov 22 17:53:56 svc.startd[1221]: system/sysevent:default failed fatally: transitioned to maintenance (see 'svcs -xv' for details)
Requesting System Maintenance Mode
(See /lib/svc/share/README for more information.)
Console login service(s) cannot run
Root password for system maintenance (control-d to bypass):
single-user privilege assigned to /dev/console.
Entering System Maintenance Mode
Nov 22 17:55:10 su: 'su root' succeeded for root on /dev/console
Oracle Corporation SunOS 5.10 Generic Patch January 2005
# more /etc/hosts
#
# Internet host table
#
127.0.0.1 localhost loghost
::1 localhost loghost
And there's a device inside the zone for igb1 now:
Code:
# ls /dev/ig*
/dev/igb1
But when I try to plumb it I get
# ifconfig igb1 plumb
ifconfig: cannot plumb igb1: Datalink does not exist
#
This seems to be the missing link (sorry). If I could get the s10zone to plumb igb1, all might be well. Is there perhaps some magic word I need to give in zonecfg:net?
Hi Gurus
I am not able to ping the local zone from global zone
when i am trying to ping i am getting below
ICMP Host Unreachable from gateway zone ( 192.268.35.210)
for icmp from zone ( 192.168.35.210) to sun1 ( 192.168.35.210)
However i can ping local zone from global
please... (12 Replies)
Hello,
I have a V120 server with two network interfaces. I would like to use one of them in my non global zone. I set the "ip-type=exclusive" as described here Solaris 10 8/07: Exclusive-IP Non-Global Zones (System Administration Guide: Solaris Containers-Resource Management and Solaris Zones) -... (2 Replies)
Dears,
I would like to convert solaris 10 x86 and solaris 10 sparc (Global Zones) physical servers into Local zones.
i found a document which seems to be helpful but i'm stuck @ the 1st step.
to test this i want to do it 1st on x86 system running under vmware ESXi and if it succeeds i will... (1 Reply)
Hi All,
does any body know how to create Virtual NIC in Solaris 10
if any one have good article or reference
kindly provide me
i try to Google
but i didn't find good one (7 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
I want a solaris zone,wich can get ip from dhcp external server
i configure my zone
net:
address not specified
allowed-address not specified
configure-allowed-address: true
physical: vnic1
defrouter not specified
vnic is linked to net0
dladm
net0 ... (6 Replies)
Hi
We took the reboot of server/global zone after that Solaris 11 share local zone not able to ping the default gateway but global zone able to ping same default gateway. I check/compare the before activity logs of global zone and local zones which looks fine to me, further IP and netmask of... (6 Replies)