I am trying to use the csplit file on a file that contains records that have more than 2048 characters on a line. The resultant split file seems to ignore the rest of the line and I lose the data.
Is there any way that csplit can handle record lengths greater than 2048?
Thanks (0 Replies)
Good day,
I've been trying to look for a way to compile the Xpdf sources in our HP-UX server, but have been failing to do so because there is no GCC installed, and I don't have privileges to install GCC. I was looking for a functionality to convert PDF files to .txt, which is exactly like the... (2 Replies)
I'm running a simulation (programmed in C) which makes calls to gnuplot periodically to plot data I have stored.
First I open a pipe to gnuplot and set it to multiplot:
FILE * pipe = popen("gnuplot", "w");
fprintf(pipe, "set multiplot\n");
fflush(pipe);
(this pipe stays open until the... (0 Replies)
Hi,
I need a documentation about limitations on the linux partition. On how many primary and extended I could create. And also on different type of storage, how many big capacity I can create.
Thanks. (3 Replies)
Hi,
I have used pdftotext with good results in the past, but today for some reason I keep getting the same error message.
My command is as follows:
And the error message is
I am using Vmware player with Ubuntu server, but I don't think that is causing this issue as I have been using... (2 Replies)
Hi,
I have noticed some performance issues on my RHEL5 server but the memory and CPU utilization on the box is fine.
I have a 1G full duplexed eth0 card and I am suspicious that this may be causing the problem. My eth0 settings are as follows:
Settings for eth0:
Supported ports: ... (12 Replies)
Hi,
I recently started working with Solaris, and what I noticed is that a lot of commands I used to regularly use don't work, like sed -i and grep -r. I have found work arounds for these problems though but it's a pain in the ass.
I'm just wondering why they decided not to include these handy... (4 Replies)
In recently reading an article on linux basics before I embark and my personal installation project I came across this passage -
IDE drives have three types of partition: primary, logical, and extended. The partition table is located in the master boot record (MBR) of a disk. The MBR is the... (12 Replies)
I have a directory having a number of pdf files.
I want to convert all the files to text, stored in a single text file
The following creates multiple text files
ls *.pdf | xargs -n1 pdftotext (1 Reply)
Discussion started by: kristinu
1 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)