11-09-2019
Move root disk to new identical hardware
We have in a couple of occasions moved root disk & flashcard in netra 240 to new identical hardware instead of replacing mb in dead server. Flashcard is to preserve mac adresses and mainly hostid for license stuff. Works without doing anything other than poweron & boot.
Now we have a similar issue with a vfire 445. Can we move working root disk & idprom from sc to new identical hardware.
Ps
In both situations svm is also in play( metastat etc.)
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
I removed an external Sun disk (with data on it) from an old 2.6 system and added the disk to another 2.6 system. The new system seems to recognize the system (verified by the format command).
When try to mount I am getting, I got the error:
mount: /dev/dsk/c1t1d0s6 is not this fstype.
I... (3 Replies)
Discussion started by: sunshine
3 Replies
2. UNIX for Dummies Questions & Answers
Hi all,
I purchased a pci controller card and a 3rd hard drive to put Linux on my machine. The card did not enable me to boot to the 3rd drive so I could not get Mandrake to install. My motherboard is a Gigabyte GA-7DXR+. Can anyone point me to a reasonable card/connector which will allow me... (2 Replies)
Discussion started by: onestepto
2 Replies
3. Solaris
Hi,
I need to do an installation where I have identical hardware at both sites and create the installation at one site and take the disk to the other site. Question: Do I need to do anything special for the OS to come up properly?
thanks. (18 Replies)
Discussion started by: VirginiaSA
18 Replies
4. Solaris
Hi,
df -h display:
# df -h
Filesystem size used avail capacity Mounted on
/dev/dsk/c1t0d0s0 9.8G 8.1G 1.7G 84% /
/proc 0K 0K 0K 0% /proc
mnttab 0K 0K 0K 0% /etc/mnttab
fd 0K 0K 0K 0% /dev/fd
swap 1.0G 152K 1.0G 1% /var/run
swap 1.1G 24M 1.0G 3% /tmp
/dev/dsk/c1t0d0s3 57G 13G 43G 24%... (4 Replies)
Discussion started by: lamoul
4 Replies
5. Solaris
Hi,
The disks of my servers are getting full and I need to move the /export/home partition on to a new set of disks. I already have 2 mirrored disks and have added 2 more and mirrored them after creating the filesystem on them.
Do I just need to edit the /etc/vfstab and point the /export/home... (1 Reply)
Discussion started by: run_time_error
1 Replies
6. Solaris
We have hardware RAID configured on Sun-Blade-T6320 and one of the disk got failed. Hence we replaced the failed disk. But the hot swapped disk not recognized by RAID. Kindly help on fixing this issue.
We have 2 LDOM configured on this server and this server running on single disk.
#... (8 Replies)
Discussion started by: rock123
8 Replies
7. Solaris
Hi All
Hope it's okay to post on this sub-forum, couldn't find a better place
I've got a 480R running solaris 8 with veritas volume manager managing all filesystems, including an encapsulated root disk (I believe the root disk is encapsulated as one of the root mirror disks has an entry under... (1 Reply)
Discussion started by: sunnyd76
1 Replies
8. UNIX for Dummies Questions & Answers
Hi,
I have server with 2 active disk, but disk 1 contain big part of os is falling,
how can i move everything to disk 2 and then remove the disk 1?
Thanks (4 Replies)
Discussion started by: prpkrk
4 Replies
9. Solaris
Hi Guys,
One of two disks in my solaris machine has failed, the name is disk0, this is SUN physical sparc machine
But I work remotely, so people working near that physical server are not that technical, so from OS command prompt can run some command to bink faulty disk at front panel of Server.... (9 Replies)
Discussion started by: manalisharmabe
9 Replies
10. Linux
Hi
We have RHEL 7.3 running from local disk and we want to move it to storage.
I am unable to find any proper procedure to do this activity. Please help. (4 Replies)
Discussion started by: powerAIX
4 Replies
info(4) Kernel Interfaces Manual info(4)
NAME
info - diskless client configuration information file
DESCRIPTION
The file is a POSIX shell sourceable file which contains parameter definitions used at boot time. Typically, it will be an empty file and
default values will be used for all parameters. Following is the list of parameters which can be defined in the file:
Specifies the IP address of the client's private root server. If this is not
specified, the client's private root server defaults to the boot server.
Specifies the pathname to the client's private root on the private root
server. If this is not specified, the client's private root path defaults to
Specifies the NFS mount options to mount the client's private root from
the private root server. If this is not specified, the mount options default to
Specifies the NFS mount options to mount the client's
directory from the boot server. If this is not specified, the mount options default to
Specifies whether NFS should be configured as primary swap. (NOTE: In
order to swap to NFS, a diskless kernel must be configured with tunable parameter set to 1.) If a diskless
machine has a local swap disk and swap to NFS is not desired, the parameter should be set to the value of 1
and the diskless kernel should be configured without setting to 1. If this parameter is not specified in
the file and the kernel tunable parameter is set to 1, then NFS will be configured as primary swap.
If not set, this parameter defaults to a value of 1, and results in the
removal of all swapfiles above the configured swap minimum (swap is specified in the client's when a disk-
less client boots. This ensures that extraneous swapfiles at boot time are removed, thus freeing disk
space. If is set to 0 in the file, removal of extra swapfiles is disabled. This may result in faster boot
times due to the time savings in creating additional swap files.
The file resides in the same directory as the client's kernel () on the boot server and is retrieved at boot time using command. By
default, when a diskless client is created, an empty file is placed in the client's kernel directory. This ensures that all parameters
revert to their default values (see above). If the file is not present, this is an error.
EXAMPLES
An example file is shown below:
FILES
info(4)