Looks fine.
As far as i could read online, it's some kind of Oracle Linux derivative which in turn is RHEL base.
Can we see inside the guest ..
P.S I just saw you figured it out, so you can disregard this.
You still might want to check out those network files to configure onboot network and / or static IP
Hi,
Need help for the network configuration on Solaris 10 5/8.
My NIC's dirver was loaded after Solaris installation and is configured using static ip address for a local network: 172.16.1.12
I have configured set of files as: /etc/hosts :
172.16.1.12 ls12
/etc/hostname.iprb0:... (7 Replies)
Howdy
I am using Fedora12 with KVM, with XP64pro as a guest. Everything seems to be working just fine, BUT I can't Save. When I do instruction KVM to save, I get a continuing Saving display, but it continues for a long time until I finally terminate it due to boredom :) I have let it run for... (0 Replies)
Hi Folks,
I am used to writing scripts to get info by running commands at local zones level from their respective global zone by using zlogin <localzone> "command>" while remaining at the global zone level.
Can the same be done with Guest LDoms while remaining at the control LDOM level?
... (4 Replies)
Solaris for Sparc 11.1 with the latest patches. Created a Guest LDOM with two vnet's net0 and net1, installed a guest whole root, ip exclusive zone that I want to be able to utilize DHCP. I have been able to create the zone but unable to get it to boot because I am unable to assign an anet to it.... (4 Replies)
Hi!
I am not sure if this is the right place to post this question. What I did was to download vmware onto my laptop, them install a linux distro as a guest O.S., on VM network configuration I have used "bridge", them I used Virtual Network Editor to chose the network interface, but as I write... (4 Replies)
Hi,
There is LDOM Guest where I need to expand /u02 file systems on it.
It is residing on a Solaris 11 Hypervisor (Primary Domain).
The storage is expanded on vdisk presented to Hypervisor.
I need steps to expand the /u02 on LDOM Guest. (2 Replies)
hello, I have a problem when configuring the network at the LDOM level, on a SPARC-Enterprise-T5120 machine
The network goes through VLAN 503 (level, network tagget)
And I need to give network to the guest domain: madarrwebsol10
I hope someone can bring some light ....
Excuse my English ...
... (4 Replies)
hello to everyone. im new member here.
i have a problem with a guest ldom on solaris 11 sparc in a T8. I need to access to disk vds assigned to guest domain but from control domain.
I want to modify a parameter in inittab of the guest domain because start guest domain give me problems... (2 Replies)
Discussion started by: Liam_
2 Replies
LEARN ABOUT SUSE
smpppd-ifcfg
SMPPPD-IFCFG(8) SMPPPD SMPPPD-IFCFG(8)NAME
smpppd-ifcfg - SuSE Meta PPP Daemon
DESCRIPTION
smpppd-ifcfg is a daemon that controls a single dialup connection to the internet. It does so by starting and controlling the pppd. The
configuration of the dialup connections is done by YaST2.
smpppd-ifcfg is not intended for direct use. Use ifup and ifdown or a frontend like cinternet , qinternet or kinternet instead.
OPTIONS
These options are recognized by smpppd-ifcfg. If a long option shows an argument as mandatory, then it is mandatory for the equivalent
short option also.
--up Bring the connection up. This is the default action.
--down Bring the connection down.
--status
Report status of the connection.
-i, --ifcfg=NAME
Specify the ifcfg file to use. This option is mandatory.
-p, --provider=NAME
Specify the provider file to use.
--detach
Detach from the controlling terminal. This is the default.
--nodeatch
Don't detach from the controlling terminal.
-d, --debug
Turn on debugging.
--version
Show program version and exit.
--help Show help information and exit.
FILES
/etc/sysconfig/network/ifcfg-*
Configuration files for the interfaces.
/etc/sysconfig/network/providers/*
Configuration files for the providers.
/var/log/smpppd/ifcfg-xxx.log
Log file.
/var/log/smpppd/accounting.log
File containing accounting information.
/var/run/smpppd.ifcfg-xxx.pid
Pid file.
/var/lib/smpppd/ifcfg-xxx.info
Info file with various status information.
/var/run/smpppd/ifcfg-xxx
Socket to communicate with smpppd.
SEE ALSO
kinternet, qinternet, cinternet(1), accounting(1), wvdial(1), smpppd.conf(5), pppd(8), smpppd(8).
AUTHOR
Arvin Schnell <arvin@suse.de>
SuSE December 2002 SMPPPD-IFCFG(8)