Solaris 11 LDOM guest network not working Post: 303040641

8 More Discussions You Might Find Interesting

1. Solaris

Network not working on Solaris 10

Hi, Need help for the network configuration on Solaris 10 5/8. My NIC's dirver was loaded after Solaris installation and is configured using static ip address for a local network: 172.16.1.12 I have configured set of files as: /etc/hosts : 172.16.1.12 ls12 /etc/hostname.iprb0:...

2. Virtualization and Cloud Computing

KVM FC12 guest save not working ??

Howdy I am using Fedora12 with KVM, with XP64pro as a guest. Everything seems to be working just fine, BUT I can't Save. When I do instruction KVM to save, I get a continuing Saving display, but it continues for a long time until I finally terminate it due to boredom :) I have let it run for...

3. Solaris

Help needed - trying to run commands in Guest LDoms from Control LDOM

Hi Folks, I am used to writing scripts to get info by running commands at local zones level from their respective global zone by using zlogin <localzone> "command>" while remaining at the global zone level. Can the same be done with Guest LDoms while remaining at the control LDOM level? ...

4. Solaris

Network Config on Zone in a Guest LDOM

Solaris for Sparc 11.1 with the latest patches. Created a Guest LDOM with two vnet's net0 and net1, installed a guest whole root, ip exclusive zone that I want to be able to utilize DHCP. I have been able to create the zone but unable to get it to boot because I am unable to assign an anet to it....

5. UNIX for Dummies Questions & Answers

Configure network connectivity as guest O.S under vmware

Hi! I am not sure if this is the right place to post this question. What I did was to download vmware onto my laptop, them install a linux distro as a guest O.S., on VM network configuration I have used "bridge", them I used Virtual Network Editor to chose the network interface, but as I write...

6. Solaris

Disk expansion on LDOM Guest

Hi, There is LDOM Guest where I need to expand /u02 file systems on it. It is residing on a Solaris 11 Hypervisor (Primary Domain). The storage is expanded on vdisk presented to Hypervisor. I need steps to expand the /u02 on LDOM Guest.

7. Solaris

LDOM Solaris 11 add Network vsw (Virtual switch)

hello, I have a problem when configuring the network at the LDOM level, on a SPARC-Enterprise-T5120 machine The network goes through VLAN 503 (level, network tagget) And I need to give network to the guest domain: madarrwebsol10 I hope someone can bring some light .... Excuse my English ... ...

8. Solaris

Ldom guest volumen problem t8 Solaris 11

hello to everyone. im new member here. i have a problem with a guest ldom on solaris 11 sparc in a T8. I need to access to disk vds assigned to guest domain but from control domain. I want to modify a parameter in inittab of the guest domain because start guest domain give me problems...

LEARN ABOUT CENTOS

grub-file

GRUB-FILE(1)                                                       User Commands                                                      GRUB-FILE(1)

NAME

       grub-file - check file type

SYNOPSIS

       file OPTIONS FILE

DESCRIPTION

       Check if FILE is of specified type.

       --is-i386-xen-pae-domu
              Check if FILE can be booted as i386 PAE Xen unprivileged guest kernel

       --is-x86_64-xen-domu
              Check if FILE can be booted as x86_64 Xen unprivileged guest kernel

       --is-x86-xen-dom0
              Check if FILE can be used as Xen x86 privileged guest kernel

       --is-x86-multiboot
              Check if FILE can be used as x86 multiboot kernel

       --is-x86-multiboot2 Check if FILE can be used as x86 multiboot2 kernel

       --is-arm-linux
              Check if FILE is ARM Linux

       --is-arm64-linux
              Check if FILE is ARM64 Linux

       --is-ia64-linux
              Check if FILE is IA64 Linux

       --is-mips-linux
              Check if FILE is MIPS Linux

       --is-mipsel-linux
              Check if FILE is MIPSEL Linux

       --is-sparc64-linux
              Check if FILE is SPARC64 Linux

       --is-powerpc-linux
              Check if FILE is POWERPC Linux

       --is-x86-linux
              Check if FILE is x86 Linux

       --is-x86-linux32
              Check if FILE is x86 Linux supporting 32-bit protocol

       --is-x86-kfreebsd
              Check if FILE is x86 kFreeBSD

       --is-i386-kfreebsd
              Check if FILE is i386 kFreeBSD

       --is-x86_64-kfreebsd
              Check if FILE is x86_64 kFreeBSD

       --is-x86-knetbsd
              Check if FILE is x86 kNetBSD

       --is-i386-knetbsd
              Check if FILE is i386 kNetBSD

       --is-x86_64-knetbsd Check if FILE is x86_64 kNetBSD

       --is-i386-efi
              Check if FILE is i386 EFI file

       --is-x86_64-efi
              Check if FILE is x86_64 EFI file

       --is-ia64-efi
              Check if FILE is IA64 EFI file

       --is-arm64-efi
              Check if FILE is ARM64 EFI file

       --is-arm-efi
              Check if FILE is ARM EFI file

       --is-hibernated-hiberfil
              Check if FILE is hiberfil.sys in hibernated state

       --is-x86_64-xnu
              Check if FILE is x86_64 XNU (Mac OS X kernel)

       --is-i386-xnu
              Check if FILE is i386 XNU (Mac OS X kernel)

       --is-xnu-hibr
              Check if FILE is XNU (Mac OS X kernel) hibernated image

       --is-x86-bios-bootsector
              Check if FILE is BIOS bootsector

       -h, --help              Display this help and exit.  -u, --usage             Display the usage of this command and exit.

SEE ALSO

       The  full documentation for grub-file is maintained as a Texinfo manual.  If the info and grub-file programs are properly installed at your
       site, the command

              info grub-file

       should give you access to the complete manual.

grub-file (GRUB) 2.02-2ubuntu8.3                                     July 2018                                                        GRUB-FILE(1)