I'm really stuck here. I've created an LDOM on a SPARC T4-1 with Solaris 11.4 to run a copy of Linux for SPARC. I got the Linux ISO installed and Linux itself installed and booted OK. The only thing is is that there's no networking available in the Linux guest.
This question is basically the same as this one: LDOM Solaris 11 add Network vsw (Virtual switch) but I wasn't able to figure it out even after reading that. Can someone please help me with this particular case?
Here's the same info Wittman gave in his OP:
Code:
root@hemlock:/etc# ipadm
NAME CLASS/TYPE STATE UNDER ADDR
lo0 loopback ok -- --
lo0/v4 static ok -- 127.0.0.1/8
lo0/v6 static ok -- ::1/128
net0 ip ok -- --
net0/v4 static ok -- 192.168.0.183/24
net0/v6 addrconf ok -- fe80::210:e0ff:fe8a:1138/10
sp-phys0 ip ok -- --
sp-phys0/v4 static ok -- 169.254.182.77/24
root@hemlock:/etc#
And
Code:
root@hemlock:/etc# dladm show-phys
LINK MEDIA STATE SPEED DUPLEX DEVICE
net0 Ethernet up 100 full igb0
net1 Ethernet unknown 0 unknown igb1
net2 Ethernet unknown 0 unknown igb2
net3 Ethernet unknown 0 unknown igb3
net4 Ethernet up 100 full vsw0
sp-phys0 Ethernet up 10 full usbecm2
root@hemlock:/etc# ldm list
NAME STATE FLAGS CONS VCPU MEMORY UTIL NORM UPTIME
primary active -n-cv- UART 8 40192M 11% 11% 6d 18h 14m
linux active -n---- 5000 8 4G 0.0% 0.0% 1h 29m
root@hemlock:/etc# dladm show-link
LINK CLASS MTU STATE OVER
ldoms-vsw0.vport0 vnic 1500 up net0
ldoms-vsw0.vport1 vnic 1500 up net0
net0 phys 1500 up --
net1 phys 1500 unknown --
net2 phys 1500 unknown --
net3 phys 1500 unknown --
net4 phys 1500 up --
sp-phys0 phys 1500 up --
root@hemlock:/etc#
Hi,
Need help for the network configuration on Solaris 10 5/8.
My NIC's dirver was loaded after Solaris installation and is configured using static ip address for a local network: 172.16.1.12
I have configured set of files as: /etc/hosts :
172.16.1.12 ls12
/etc/hostname.iprb0:... (7 Replies)
Howdy
I am using Fedora12 with KVM, with XP64pro as a guest. Everything seems to be working just fine, BUT I can't Save. When I do instruction KVM to save, I get a continuing Saving display, but it continues for a long time until I finally terminate it due to boredom :) I have let it run for... (0 Replies)
Hi Folks,
I am used to writing scripts to get info by running commands at local zones level from their respective global zone by using zlogin <localzone> "command>" while remaining at the global zone level.
Can the same be done with Guest LDoms while remaining at the control LDOM level?
... (4 Replies)
Solaris for Sparc 11.1 with the latest patches. Created a Guest LDOM with two vnet's net0 and net1, installed a guest whole root, ip exclusive zone that I want to be able to utilize DHCP. I have been able to create the zone but unable to get it to boot because I am unable to assign an anet to it.... (4 Replies)
Hi!
I am not sure if this is the right place to post this question. What I did was to download vmware onto my laptop, them install a linux distro as a guest O.S., on VM network configuration I have used "bridge", them I used Virtual Network Editor to chose the network interface, but as I write... (4 Replies)
Hi,
There is LDOM Guest where I need to expand /u02 file systems on it.
It is residing on a Solaris 11 Hypervisor (Primary Domain).
The storage is expanded on vdisk presented to Hypervisor.
I need steps to expand the /u02 on LDOM Guest. (2 Replies)
hello, I have a problem when configuring the network at the LDOM level, on a SPARC-Enterprise-T5120 machine
The network goes through VLAN 503 (level, network tagget)
And I need to give network to the guest domain: madarrwebsol10
I hope someone can bring some light ....
Excuse my English ...
... (4 Replies)
hello to everyone. im new member here.
i have a problem with a guest ldom on solaris 11 sparc in a T8. I need to access to disk vds assigned to guest domain but from control domain.
I want to modify a parameter in inittab of the guest domain because start guest domain give me problems... (2 Replies)