Today i try same installation on VirtualBox on my home PC. Results is same.
Solaris 11.4
Cluster 4.4
i will attach log file with errors from installation process...
Quote:
No autodiscovery results returned from node "sclr2".
Probes were sent out from all transport adapters configured for this
node ("sclr1"). But, they were not seen by any of the other nodes.
This may be due to any number of reasons, including improper cabling
or a switch which was confused by the probes.
You can either attempt to correct the problem and try the probes again
or manually configure the transport. To correct the problem might
involve re-cabling, changing the configuration, or fixing hardware.
You must configure the transport manually to configure tagged VLAN
adapters and non tagged VLAN adapters on the same private interconnect
VLAN.
Code:
root@sclr1:~# ipadm show-if
IFNAME CLASS STATE ACTIVE OVER
lo0 loopback ok yes --
ipmp0 ipmp ok yes net0
net0 ip ok yes --
root@sclr1:~#
Code:
root@sclr2:~# ipadm show-if
IFNAME CLASS STATE ACTIVE OVER
lo0 loopback ok yes --
ipmp0 ipmp ok yes net0
net0 ip ok yes --
root@sclr2:~#
Code:
root@sclr1:~# dladm show-phys
LINK MEDIA STATE SPEED DUPLEX DEVICE
net0 Ethernet up 1000 full e1000g0
net1 Ethernet unknown 1000 full e1000g1
net2 Ethernet unknown 1000 full e1000g2
root@sclr1:~# ipadm show-if
IFNAME CLASS STATE ACTIVE OVER
lo0 loopback ok yes --
net0 ip ok yes --
root@sclr1:~#
Code:
root@sclr2:~# dladm show-phys
LINK MEDIA STATE SPEED DUPLEX DEVICE
net0 Ethernet up 1000 full e1000g0
net1 Ethernet unknown 1000 full e1000g1
net2 Ethernet unknown 1000 full e1000g2
root@sclr2:~# ipadm show-if
IFNAME CLASS STATE ACTIVE OVER
lo0 loopback ok yes --
net0 ip ok yes --
root@sclr2:~#
Code:
root@sclr2:~# ifconfig net1 plumb 172.16.1.2 netmask 255.255.248.0 private up
root@sclr2:~# ping -sR 172.16.1.1
PING 172.16.1.1: 56 data bytes
64 bytes from 172.16.1.1: icmp_seq=0. time=0.375 ms
64 bytes from 172.16.1.1: icmp_seq=1. time=0.335 ms
64 bytes from 172.16.1.1: icmp_seq=2. time=0.380 ms
^C
----172.16.1.1 PING Statistics----
3 packets transmitted, 3 packets received, 0% packet loss
round-trip (ms) min/avg/max/stddev = 0.335/0.363/0.380/0.025
root@sclr2:~#
After much hitting my head to the wall with this meesages
root@crasher /workzone/dvd4_sfb-sol_x64]#./installer -verbose -installonly
5.0MP3 Installation Program
Copyright (c) 2008 Symantec Corporation. All rights reserved. Symantec, the Symantec... (1 Reply)
Greetings Forumers!
I tried installing Solaris Cluster 3.3 today. I should say I tried configuring the Cluster today. The software is already installed on two systems. I am trying to configure a shared filesystem between two 6320 Blades. I selected the "Custom" install because the "Typical"... (2 Replies)
Anybody have any ideas on what could be causing this crash? This an x86 virtual machine I have running in ESXi at my house, so obviously no way to send the data to Oracle for analysis. Just curious if anyone has any ideas. I suspect motherboard problems with the x86 hardware, as I already... (4 Replies)
how do I remote install a vib on 200 esxi hosts ?
I need to ssh into the host
run this command
esxcli software vib install -v /tmp/vib --no-sig-check (1 Reply)
Hi
i have 2 esxi. one is amd based cpu and the other is intel based cpu.
i have a redhat linux machine that was created in amd cpu esxi, now i need to migrate it (powered off) to INTEL based esxi. will the redhat machine will be OK with that?
Thanks (2 Replies)
Hi All,
Can any one Explain Me Step by Step installing SCO 5.0.7v in ESXi 6.0 ??
When i was trying to install its is not booting into operating systems !!
showing an error no operating systems in media !!
Thanks in Advance!! Please take some time in helping me !!
Kanthi Kiran K (3 Replies)
Tl;dr Solaris 11.4 won't boot on 2 machines because of what I believe is network issues. Need to know where I can find more info to troubleshoot.
I have two Solaris 11.4 systems running on VMware ESXi 6.5u2, which have suddenly (and seemingly for no reason) started boot-looping.
Both of... (2 Replies)