Hello. I'm writing an awk script that looks at a .csv file and calculates the weighted grade based on the scores and categories in the file. I keep getting a fatal division by zero attempted error and I know what it means but I've been looking over the code for awhile and am not sure what is causing it. Here is the code that I have:
Thought i should start this has a new thread.
i am stuck on the following question, but after learning more unix, i have written an answer to it. Can anyone check to see if it is correct and what improvements need to be made?
Question:
Write a pipeline that updates the content of a file (a... (0 Replies)
Hello,
I am searching for a way to calculate for example 10/100 within a shellscript and the result should be 0.1 and not just 0.
Every alternative i tried just results 0
Thank you in advance
2retti (6 Replies)
hi,
The below commands result only the whole number(not giving the decimal values).
pandeeswaran@ubuntu:~$ echo 1,2,3,4|sed 's/,/\//g'|bc
0
pandeeswaran@ubuntu:~$ echo 1000,2,3|sed 's/,/\//g'|bc
166
How to make it to return the decimal values?
Thanks (5 Replies)
when i try the snippet in the console its working fine:
ps awwwux | grep php-fpm | grep -v grep | grep -v master | awk '{total_mem = $6 * 1024 + total_mem; total_proc++} END{printf("%d\n", total_mem / total_proc)}'
output:
but when i try the bash script:
#!/bin/sh
# -*- sh -*-
#... (3 Replies)
I want to implement the below formula with awk oneliner
new_value = ((old_value - old_min) / (old_max - old_min) ) * (new_max - new_min) + new_min
I want to pass the value of old_min and old_min as variable. Here is what I did for this
old_min=$(awk 'BEGIN{a=100000000000}{if ($10<0+a) a=$10}... (2 Replies)
Today, I noticed some errors in our SSL cert renewal log files, mostly related to domains where the IP address had changed. Concerned about this, rebuilt out SSL cert, which normally goes well without a hiccup.
However, for today, for some reason which I cannot explain, there was a PHP error... (0 Replies)
Discussion started by: Neo
0 Replies
LEARN ABOUT MINIX
total
TOTAL(1) General Commands Manual TOTAL(1)NAME
total - sum up columns
SYNOPSIS
total [ -m ][ -sE | -p | -u | -l ][ -i{f|d}[N] ][ -o{f|d} ][ -tC ][ -N [ -r ]] [ file .. ]
DESCRIPTION
Total sums up columns of real numbers from one or more files and prints out the result on its standard output.
By default, total computes the straigt sum of each input column, but multiplication can be specified instead with the -p option. Likewise,
the -u option means find the upper limit (maximum), and -l means find the lower limit (minimum).
Sums of powers can be computed by giving an exponent with the -s option. (Note that there is no space between the -s and the exponent.)
This exponent can be any real number, positive or negative. The absolute value of the input is always taken before the power is computed
in order to avoid complex results. Thus, -s1 will produce a sum of absolute values. The default power (zero) is interpreted as a straight
sum without taking absolute values.
The -m option can be used to compute the mean rather than the total. For sums, the arithmetic mean is computed. For products, the geomet-
ric mean is computed. (A logarithmic sum of absolute values is used to avoid overflow, and zero values are silently ignored.)
If the input data is binary, the -id or -if option may be given for 64-bit double or 32-bit float values, respectively. Either option may
be followed immediately by an optional count, which defaults to 1, indicating the number of double or float binary values to read per
record on the input file. (There can be no space between the option and this count.) Similarly, the -od and -of options specify binary
double or float output, respectively. These options do not need a count, as this will be determined by the number of input channels.
A count can be given as the number of lines to read before computing a result. Normally, total reads each file to its end before producing
its result, but this behavior may be overridden by inserting blank lines in the input. For each blank input line, total produces a result
as if the end-of-file had been reached. If two blank lines immediately follow each other, total closes the file and proceeds to the next
one (after reporting the result). The -N option (where N is a decimal integer) tells total to produce a result and reset the calculation
after every N input lines. In addition, the -r option can be specified to override reinitialization and thus give a running total every N
lines (or every blank line). If the end of file is reached, the current total is printed and the calculation is reset before the next file
(with or without the -r option).
The -tC option can be used to specify the input and output tab character. The default tab character is TAB.
If no files are given, the standard input is read.
EXAMPLE
To compute the RMS value of colon-separated columns in a file:
total -t: -m -s2 input
To produce a running product of values from a file:
total -p -1 -r input
BUGS
If the input files have varying numbers of columns, mean values will certainly be off. Total will ignore missing column entries if the tab
separator is a non-white character, but cannot tell where a missing column should have been if the tab character is white.
AUTHOR
Greg Ward
SEE ALSO cnt(1), neaten(1), rcalc(1), rlam(1), tabfunc(1)RADIANCE 2/3/95 TOTAL(1)