I have the below script I am running on a Solaris system to check the status of a Tivoli Workload Scheduler job and return the status. We need this script to return a '0' if any of the jobs in the stream are in a "EXEC" state and an "1" if in a "HOLD" state. I am not a programmer so I am not sure... (1 Reply)
Suppose I have a script which is monitoring a directory
whenever a file drops in that directory,it sends alert
say I want to write a return code for the above script
which on successful execution of script gives a return value
Based on return code , I want to do initiate some jobs in other... (1 Reply)
Hi,
Can anyone tell me if there are return codes for SFTP? If so how would you capture them? I've tried 'man sftp' but its not particularly helpful.
Many thanks
Helen :confused: (4 Replies)
Hi,
I am trying to figure out how to test to see if a server is accepting telnet connections via a script.
I have several remote MPE servers that are set in single user mode (and hence not accepting telnet connections), for their backups, I want to try and automate a test (from a unix... (0 Replies)
Can any body please tell me the return codes of RDIST tool?
I am using RDIST (through an UNIX script) to synchronize files between two servers say ukblx151(source) & ukapx050(target).
RDIST raises an alert mail (through notify option) in case of success & also failure but there is a problem if... (0 Replies)
Hi
In an unix script I am using an Perl one liner perl -i -ne '-----'
If the perl one liner fails i am not able to catch the return code.
It always give 0 as return code. Can you tell me how can i catch the return code
perl -i -ne '---'
RETCODE=$?
echo $RETCODE
Thanks and Regards
Ammu (2 Replies)
sftp -v b $putlist $SFTP_ID@TARGET_SERVER
How can I get a return code if fails to put the file?
sftp -v b $getlist $SFTP_ID@TARGET_SERVER
How can I get a return code if fails to put the file? (1 Reply)
Hi,
I wanted to know the significance of different return codes when we do echo $?
I know when $? returns 0 the command has worked successfully.
but what does $? = 1, 2, 3 etc. signify.
Thanks in advance for the help !!! (3 Replies)
Not sure if this is of any use but......
I was messing around with getting return codes greater than 255 for special usage...
Of course the code could be made simple but in this code the new stored return code
is generated as exit is progressing...
#!/bin/sh
# Real and imaginary return... (9 Replies)
Discussion started by: wisecracker
9 Replies
LEARN ABOUT OPENSOLARIS
bvnc
bssh/bvnc/bshell(1) General Commands Manual bssh/bvnc/bshell(1)NAME
bssh/bvnc/bshell - Browse for SSH/VNC servers on the local network
SYNOPSIS
bssh
bvnc
bshell
DESCRIPTION
bssh/bvnc/bshell browses for SSH/VNC servers on the local network, shows them in a GUI for the user to select one and finally calls
ssh/vncviewer after a selection was made.
If the binary is called as bssh only ssh servers will be shown. If the binary is called as bvnc only VNC servers will be shown. If the
binary is called as bshell both VNC and SSH servers are shown.
OPTIONS -s | --ssh
Browse for SSH servers (and only SSH servers) regardless under which name the binary is called.
-v | --vnc
Browse for VNC servers (and only VNC servers) regardless under which name the binary is called.
-S | --shell
Browse for both VNC and SSH servers regardless under which name the binary is called.
-d | --domain= DOMAIN
Browse in the specified domain. If omitted bssh/bvnc/bshell will browse in the default browsing domain (usually .local)
-h | --help
Show help.
SEE ALSO avahi-browse(1), ssh(1), vncviewer(1)COMMENTS
This man page was written using xml2man(1) by Oliver Kurth.
Manuals User bssh/bvnc/bshell(1)