I have the below script I am running on a Solaris system to check the status of a Tivoli Workload Scheduler job and return the status. We need this script to return a '0' if any of the jobs in the stream are in a "EXEC" state and an "1" if in a "HOLD" state. I am not a programmer so I am not sure... (1 Reply)
Suppose I have a script which is monitoring a directory
whenever a file drops in that directory,it sends alert
say I want to write a return code for the above script
which on successful execution of script gives a return value
Based on return code , I want to do initiate some jobs in other... (1 Reply)
Hi,
Can anyone tell me if there are return codes for SFTP? If so how would you capture them? I've tried 'man sftp' but its not particularly helpful.
Many thanks
Helen :confused: (4 Replies)
Hi,
I am trying to figure out how to test to see if a server is accepting telnet connections via a script.
I have several remote MPE servers that are set in single user mode (and hence not accepting telnet connections), for their backups, I want to try and automate a test (from a unix... (0 Replies)
Can any body please tell me the return codes of RDIST tool?
I am using RDIST (through an UNIX script) to synchronize files between two servers say ukblx151(source) & ukapx050(target).
RDIST raises an alert mail (through notify option) in case of success & also failure but there is a problem if... (0 Replies)
Hi
In an unix script I am using an Perl one liner perl -i -ne '-----'
If the perl one liner fails i am not able to catch the return code.
It always give 0 as return code. Can you tell me how can i catch the return code
perl -i -ne '---'
RETCODE=$?
echo $RETCODE
Thanks and Regards
Ammu (2 Replies)
sftp -v b $putlist $SFTP_ID@TARGET_SERVER
How can I get a return code if fails to put the file?
sftp -v b $getlist $SFTP_ID@TARGET_SERVER
How can I get a return code if fails to put the file? (1 Reply)
Hi,
I wanted to know the significance of different return codes when we do echo $?
I know when $? returns 0 the command has worked successfully.
but what does $? = 1, 2, 3 etc. signify.
Thanks in advance for the help !!! (3 Replies)
Not sure if this is of any use but......
I was messing around with getting return codes greater than 255 for special usage...
Of course the code could be made simple but in this code the new stored return code
is generated as exit is progressing...
#!/bin/sh
# Real and imaginary return... (9 Replies)
Discussion started by: wisecracker
9 Replies
LEARN ABOUT OPENSOLARIS
scp
scp(1) User Commands scp(1)NAME
scp - secure copy (remote file copy program)
SYNOPSIS
scp [-pqrvBC46] [-F ssh_config] [-S program] [-P port]
[-c cipher] [-i identity_file] [-o ssh_option]
[ [user@]host1:]file1 []... [ [user@]host2:]file2
DESCRIPTION
The scp utility copies files between hosts on a network. It uses ssh(1) for data transfer, and uses the same authentication and provides
the same security as ssh(1). Unlike rcp(1), scp will ask for passwords or passphrases if they are needed for authentication.
Any file name may contain a host and user specification to indicate that the file is to be copied to/from that host. Copies between two
remote hosts are permitted.
OPTIONS
The following options are supported:
-4 Forces scp to use IPv4 addresses only.
-6 Forces scp to use IPv6 addresses only.
-B Selects batch mode. (Prevents asking for passwords or passphrases.)
-c cipher Selects the cipher to use for encrypting the data transfer. This option is directly passed to ssh(1).
-C Compression enable. Passes the -C flag to ssh(1) to enable compression.
-F ssh_config Specifies an alternative per-user configuration file for ssh(1.).
-i identity_file Selects the file from which the identity (private key) for RSA authentication is read. This option is directly passed
to ssh(1).
-o ssh_option The given option is directly passed to ssh(1).
-p Preserves modification times, access times, and modes from the original file.
-P port Specifies the port to connect to on the remote host. Notice that this option is written with a capital `P', because -p
is already reserved for preserving the times and modes of the file in rcp(1).
-q Disables the progress meter.
-r Recursively copies entire directories.
-S program Specifies the name of the program to use for the encrypted connection. The program must understand ssh(1) options.
-v Verbose mode. Causes scp and ssh(1) to print debugging messages about their progress. This is helpful in debugging con-
nection, authentication, and configuration problems.
OPERANDS
The following operands are supported:
host1, host2,... The name(s) of the host from or to which the file is to be copied.
file1, file2,... The file(s) to be copied.
EXIT STATUS
The following exit values are returned:
0 Successful completion.
1 An error occurred.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWsshu |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO rcp(1), ssh(1), ssh-add(1), ssh-agent(1), ssh-keygen(1), sshd(1M), ssh_config(4), attributes(5)NOTES
Generally, use of scp with password or keyboard-interactive authentication method and two remote hosts does not work. It does work with
either the pubkey, hostbased or gssapi-keyex authentication method. For the pubkey authentication method, either private keys not pro-
tected by a passphrase, or an explicit ssh agent forwarding have to be used. The gssapi-keyex authentication method works with the ker-
beros_v5 GSS-API mechanism, but only if the GSSAPIDelegateCredentials option is enabled.
SunOS 5.11 22 Jun 2007 scp(1)