10-10-2019
OSR6 has automatic device configuration. It should have found the second disk by itself . Did you run the bios raid configurator and change the raid1 pair to be system drive 1 instead of 0.
This User Gave Thanks to jgt For This Post:
10 More Discussions You Might Find Interesting
1. SCO
I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller .
how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6.
Plz help with any idea
karzon (1 Reply)
Discussion started by: karzon
1 Replies
2. SCO
recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Discussion started by: prakrithi
3 Replies
3. Solaris
hi
this may be a very stupid question, but im quite new to Solaris (gonna buid my first system, Solaris 10 on x86 system, connected to other windows systems in a home network)
i wanna put a RAID 5 system in there to back up my other systems at home; iv read that its really so easy with SVM to... (4 Replies)
Discussion started by: Landser
4 Replies
4. Hardware
Hi,
We have a Sunfire 4150 with On-Board Internal Raid Controller connected to 4 X 146 GB SAS disks.
This also has an External Raid Controller (Storagetek Eight-Port, External HBA
Model SG-XPCIESAS-R-EXT-Z) connected to a JBOD array ( Storagetek XTA2530 ) which has 5 X 300 GB Hard disk.
... (1 Reply)
Discussion started by: ranjansukumar
1 Replies
5. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
6. AIX
Hello folks,
Could someone tell me why I unable to create pdisks for a RAID Array
# lscfg | grep scsi
+ sisscsia0 U787A.001.DPM0707-P1 PCI-X Dual Channel Ultra320 SCSI Adapter
+ scsi0 U787A.001.DPM0707-P1-T10 PCI-X Dual Channel Ultra320 SCSI Adapter... (12 Replies)
Discussion started by: filosophizer
12 Replies
7. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
8. SCO
Hello
I'm trying to virtualize an instance of Sco Unix 5.0.5 in VirtualBox (called VM-A) , but sco I have problems set to launch with the new raid controller .
The physical machine has a raid controller adaptec (alad driver) but VirtualBox uses buslogic (blc driver)
What ... (3 Replies)
Discussion started by: flako
3 Replies
9. Red Hat
Hello,
I am using Red Hat 2.6.23.1 with RAID 6 controller (card).
(When I use "cat /proc/partitions" I do not see the separate HDDs in the RAID, I see one drive for the RAID itself, as it is considered 1 large drive.)
I used a "dd" check to test my RAID drive speed and found it was a bit slow,... (7 Replies)
Discussion started by: Dbugy
7 Replies
10. SCO
Hi
I hope this is the right forum.
I am attempting to install SCO 5.0.7 on a Proliant DL380 G7 with a Smart Array P410I Controller.
I need a driver for this. Can anybody point me to a download?
Thanks in anticipation. (12 Replies)
Discussion started by: Stuart1946
12 Replies
chs(7D) Devices chs(7D)
NAME
chs - IBM ServeRAID PCI host adapter driver
DESCRIPTION
The chs driver is the IBM ServeRAID PCI controller driver.
PRECONFIGURATION
Known Problems and Limitations
To prevent data loss, a SCSI disk drive that is not defined as part of any physical pack within a logical drive will not be accessible
through the Solaris operating environment.
CONFIGURATION
Auto-configuration code determines whether the adapter is present at the configured address and what types of devices are attached to it.
The IBM ServeRAID is primarily used as a disk array (system drive) controller.
To configure the attached disk arrays, you must configure the controller (using the configuration utilities provided by the hardware manu-
facturer) before booting the Solaris operating environment You use the configuration utilities to set RAID levels, stripe parameters, cache
mechanisms and perform other functions. For more information, see the user manual supplied with your hardware.
FILES
/kernel/drv/chs.conf chs configuration file
/dev/dsk/cndn[s|p]n block device
/dev/rdsk/cndn[s|p]n raw device where:
cn controller n
dn LUN n (0-7)
sn UNIX system slice n (0-15)
pn fdisk(1M) partition(0)
ATTRIBUTES
See attributes(5) for a description of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
|Architecture |x86 |
+-----------------------------+-----------------------------+
SEE ALSO
fdisk(1M), attributes(5), cmdk(7D)
SunOS 5.10 27 November 2000 chs(7D)