How to simulate column command in Solaris? Post: 303039586

9 More Discussions You Might Find Interesting

1. IP Networking

Simulate 'try again' case

Hi, I was searching thro the topic and could not find a thread which zeroes in on the case i'm trying to simulate. Basically I have a need to simulate DNS Try again cases, without bringing the dns_sever down (by manipulating the entries in /etc/resolv.conf under 'nameserver' tag). I am so...

2. UNIX for Dummies Questions & Answers

Newbie: Simulate unix on my pc

Hi, i am new with unix. Just came back from a course, unix basics for aix. So for me to practice, i want to install a simulation program for unix om my Windows Xp pc. Dual boot must it be. Does anybody have a suggestion for this dummy??? Thnx! Paul

3. UNIX for Advanced & Expert Users

Simulate CRON job

Does anyone know how I can simulate a cron job execution via UNIX scripting or is there a command/tool that simulate this? I have a file I called "appSchedule.txt", it contains below lines: 00 03 * * 1-6 RED start 00 06 * * 0 RED start 00 21 * * * RED stop 00 03 * * 1-6 ...

4. Programming

Tool to simulate non-sequential disk I/O (simulate db file sequential read) in C POSIX

Writing a Tool to simulate non-sequential disk I/O (simulate db file sequential read) in C POSIX I have over the years come across the same issue a couple of times, and it normally is that the read speed on SAN is absolutely atrocious when doing non-sequential I/O to the disks. Problem being of...

5. Shell Programming and Scripting

command for converting 4 column data to 1 column

dear friends I want to convert four column data to one column data. For example: from 1, 2, 3, 4 5, 6, 7, 8to 1 2 3 4 5 6 7 8what is the general command for that type of convertion. thanks

6. Shell Programming and Scripting

awk command to print only selected rows in a particular column specified by column name

Dear All, I have a data file input.csv like below. (Only five column shown here for example.) Data1,StepNo,Data2,Data3,Data4 2,1,3,4,5 3,1,5,6,7 3,2,4,5,6 5,3,5,5,6 From this I want the below output Data1,StepNo,Data2,Data3,Data4 2,1,3,4,5 3,1,5,6,7 where the second column...

7. UNIX for Dummies Questions & Answers

Sort command in one column and not effect to another column

If my data is numerical : 1 = 101 2 = 102 3 = 104 4 = 104 7 = 103 8 = 103 9 = 105 I need the result like below: 1 = 101 2 = 102 3 = 103 4 = 103 7 = 104 8 = 104 9 = 105

8. Red Hat

Simulate Storage

Hello, I wanted to simulate SAN on my VMware PLayer running RHEL. Is there any tool that can be used to simulate storage setup for learning/testing? THanks,

9. Shell Programming and Scripting

Simulate enter key

I have a popup window that appears on every boot up. I would like to have it dismissed automatically each time instead of having to hit the enter key. I thought I could write a script that would execute on startup. I tried this xdotool key return andy@7_~/Downloads$ xdotool key ...

LEARN ABOUT SUSE

irsend

IRSEND(1)								FSF								 IRSEND(1)

NAME

       irsend - basic LIRC program to send infra-red commands

SYNOPSIS

       irsend [options] DIRECTIVE REMOTE CODE [CODE...]

DESCRIPTION

       Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
       as TV boxes, HiFi sets, etc.

       DIRECTIVE can be:
	  SEND_ONCE	    - send CODE [CODE ...] once
	  SEND_START	    - start repeating CODE
	  SEND_STOP	    - stop repeating CODE
	  LIST		    - list configured remote items
	  SET_TRANSMITTERS  - set transmitters NUM [NUM ...]
	  SIMULATE	    - simulate IR event

       REMOTE is the name of a remote, as described in the lircd configuration file.

       CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.

       NUM is the transmitter number of the hardware device.

       For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:

	  LIST	 ""    ""   - list all configured remote names
	  LIST REMOTE  ""   - list all codes of REMOTE
	  LIST REMOTE CODE  - list only CODE of REMOTE

       The SIMULATE command only works if it has been explicitly enabled in lircd.

       -h --help
	      display usage summary

       -v --version
	      display version

       -d --device
	      use given lircd socket [/var/run/lirc/lircd]

       -a --address=host[:port]
	      connect to lircd at this address

       -# --count=n
	      send command n times

EXAMPLES

	  irsend LIST DenonTuner ""
	  irsend SEND_ONCE  DenonTuner PROG-SCAN
	  irsend SEND_ONCE  OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
	  irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
	  irsend SEND_STOP  OnkyoAmpli VOL-DOWN
	  irsend SET_TRANSMITTERS 1
	  irsend SET_TRANSMITTERS 1 3 4
	  irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"

FILES

       /etc/lirc/lircd.conf
	      Default lircd configuration file.  It should contain all the remotes, their infra-red codes and the corresponding timing	and  wave-
	      form details.

DIAGNOSTICS

       If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
       "irsend: could not connect to socket"
       "irsend: Connection refused" (or "Permission denied").

SEE ALSO

       The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.

       lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.

irsend 0.8.7pre1						     May 2010								 IRSEND(1)