All
What is the best way to keep the system clock synchronized? I have looked at ntp and netdate. Is one good over the other? Basically I want to know if what is the most secure way to keep the system clock insync. netdate will require me to open up some port 37... is this safe? ntp also... (1 Reply)
i have an HP UNIX box w/c acts as ntp server... I tried to change the time plus 8 minutes... the problem is that the other HP UNIX ntp client did not follow the time... when I tried to restart ntp client... using stop start it only sync to the server once... when I issue the command "ntpq -p", w/c... (2 Replies)
Hi Friends,
I want a shell script which will move certain .jar files from a specified location (say /publish/content) to (/publish/archive) on every saturday morning 6 am.
One more thing to add is that before moving files it must check free space at (/publish/archive), if it is more than 60 %... (7 Replies)
All here, thank you for listening. Now I've set up a Linux NTP server by adding a external windows NTP server in /etc/ntp.conf. Then I start the ntpd daemon. But how often does the Linux NTP server update its time with the external NTP server? I've looked up everywhere but found no information... (1 Reply)
hello all,,
am trying to do a time synchronization between a ntp server and a client, but facing some problems in doing so:
i run the ntpdate in debug mode and this is what i got. please help me out..
# ntpd -d -u 172.22.1.207
ntpd 4.2.2p1@1.1570-o Sun Aug 28 19:21:03 UTC 2011 (1)... (1 Reply)
Good morning,
My first post and first visit, so hello. I have been asked to see if one of our Linux boxes can have it's time sync automatically because the person who built the system has told our staff it cannot be done. To me that raised some flags because although I am no Linux expert, I just... (12 Replies)
Discussion started by: YSupport
12 Replies
7. Post Here to Contact Site Administrators and Moderators
Dear All,
Today, somewhere around 7:30 GMT (2:30 PM Eastern Time) www.unix.com will go down for what we hope is around 15 - 20 minutes as we change out some hardware on the server.
Thank you for your patience and support.
Neo (0 Replies)
I've scheduled few jobs using cron. But they are not running .....
What might be the possible reasons ?? Also tell me how to troubleshoot.............
Please help me .......
Thanks in Advance. (2 Replies)
There is one server in my company where the time is out of sync.
When I checked (compared with other servers whose time is correct), the XNTPD variable in /etc/rc.config.d/netdaemons was set as 0.
I changed this to 1, and tried restarting the xntpd process with :
# /sbin/init.d/xntpd start
... (4 Replies)
Discussion started by: anaigini45
4 Replies
LEARN ABOUT OSF1
timedsetup
timedsetup(8) System Manager's Manual timedsetup(8)NAME
timedsetup - Performs initial setup of the time server daemon (timed).
SYNOPSIS
/usr/sbin/timedsetup
DESCRIPTION
The timedsetup command is an interactive script that can be used to perform initial time service configuration for your system.
By default, timed does not start at boot time. The timedsetup script asks if you want the timed daemon to be started at boot time, and
prompts you for any options to pass to the timed daemon whenever it is invoked. The script then starts the timed daemon.
For more information on the timed options, see the timed(8) reference page.
Note
The timed daemon is provided for compatibility. Tru64 UNIX also provides support for the Network Time Protocol (NTP) through the xntpd
daemon. Compaq recommends you use NTP for time synchronization. If your system is configured to run NTP, the timedsetup command passes
the -E and -M options to the timed daemon by default.
If you plan to run both the timed daemon and NTP, you should configure NTP first.
RESTRICTIONS
In configurations with two or more hosts each connected to the same two or more subnetworks, only one of the host can run the timed with
the -M option.
FILES
Specifies the command pathname The timed startup and shutdown script Specifies timed parameters pertinent to a specific system
SEE ALSO
Commands: timed(8), xntpd(8)timedsetup(8)