09-16-2019
What happens when you look at the arp tables, before and after?
On ethernet, as you know, the actual LAN routing is done by MAC address; so when we change IP address, we need to flush / rebuild the arp table (on both ends), generally speaking.
If we change an IP address and do not flush the arp table, there will often be an incorrect IP address <---> MAC address in the arp table and this can cause LAN routing snafus.
PS: I'm writing this based on knowledge from decades ago, off the top of my head, and have not done any research on arp in a long time.
10 More Discussions You Might Find Interesting
1. IP Networking
I have an OpenBSD 3.7 firewall with five network interfaces on it, one of which is connected to the Internet. I'd like to use the remaining four interfaces as a network switch for a single internal subnet. The main problem I have is that the DHCP daemon doesn't like multiple interfaces matching... (0 Replies)
Discussion started by: vertigo23
0 Replies
2. IP Networking
I understand how to change the ip address permanently however, I need to also make a permanent change to the subnet mask. How would I accomplish this. (5 Replies)
Discussion started by: johnparksjr
5 Replies
3. IP Networking
Hi,
My project needs to migrate the existing Subnet (255.255.255.0) to a new subnet and change the ipaddresses (currently C class). How can I do that. I need some information.
John (0 Replies)
Discussion started by: johnmarsh
0 Replies
4. Solaris
Hi,
I have a task to edit the subnet mask in almost 100+ solaris servers.Few of the servers are configured with IPMP.There will be no change of IP address or default gateway.If its a single IP we can bring NIC down,change the subnet mask in /etc/netmasks,then bring the NIC back to normal.But... (3 Replies)
Discussion started by: rajip23
3 Replies
5. AIX
I am new to this forum so please bare with me. I did search for this answer prior to posting but no luck.
Running an AIX NIM Master at 5.3TL9SP4, with about 100 clients. The subnet of one of the networks defined in the NIM env has changed. When I go to Manage Networks, Change/Show... (0 Replies)
Discussion started by: juredd1
0 Replies
6. Solaris
Hello,
can anyone help me with the command to change the subnet mask on solaris 10? The mask is currently 255.255.255.255 I will like to change it to 255.255.2555.0.
Thank you (5 Replies)
Discussion started by: cjashu
5 Replies
7. Solaris
I have a Solaris 11 machine with 2 network cables attached. The first one is the default route and is working okay. I am trying to activate the second on another subnet, but am sure missing something.
The first one is on 10.30.128. and with it everything works fine,
but when I try to add the... (0 Replies)
Discussion started by: ad101
0 Replies
8. Solaris
posted this on the other sub-forum
https://www.unix.com/unix-for-dummies-questions-and-answers/246504-solaris-11-2nd-nic-different-subnet.html
apologies if linking is not appropriate
Thanks for your help. (0 Replies)
Discussion started by: ad101
0 Replies
9. AIX
Hi Guys,
Our lpars is currently running on 2 different vlans (20, 30). Now we have a requirement that vlan 30 needs to be change to vlan 31 at the same subnet. I'm not sure on what is the best approach for this or what change is involve on the AIX side.
This is our setup.
Network switch -... (5 Replies)
Discussion started by: kaelu26
5 Replies
10. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
DAIC(4) BSD Kernel Interfaces Manual DAIC(4)
NAME
daic -- isdn4bsd driver for EICON.Diehl active ISDN cards
SYNOPSIS
daic0 at isa? iomem 0xd8000 irq 10
DESCRIPTION
The daic driver supports the old Diehl active cards: S, SX, SXn, SCOM and QUADRO.
For a QUADRO card, the driver will detect the board type and use all four ports, each attached as a controller of its own to the isdn4bsd
system, which can be listed using the daicctl utility.
The daic driver interfaces the ISDN card to the ISDN4BSD kernel subsystem. All lower layer ISDN control is handled by the card. This should
allow you to run any national ISDN protocol delivered by EICON.Diehl for your card, but the driver has only been tested with the DSS1 proto-
col and some parts of the cards interface are ISDN protocol dependent.
The daic driver is written to conform to the software interface documented by Diehl in their ISDN-Karten Benutzerhandbuch from 1992.
MICROCODE DOWNLOAD
Every active card needs its own operating software before it can work. You have to download this to the card before using it with isdn4bsd.
Use the daicctl utility to do this, i.e. call daicctl -d te_etsi.sx 1 to download the file te_etsi.sx to controller number 1. Use daicctl -l
to list all available controllers (and ports). You have to select the correct ISDN protocol file for your ISDN interface, see the Diehl docu-
mentation for details.
The cards bootstrap process involves another file, which is independent of the card type you use and the protocol you run. It is called
download.bin in current versions of the Diehl software distribution and has to be copied to the kernel compile directory under
dev/microcode/daic and converted into a header file used when compiling the kernel by running make in that directory. Your kernel compile
will fail and remind you of this if you forget to do this. Due to copyright restrictions we cannot distribute the driver with this file inte-
grated. But if you own a card, you do have the file (or can get it from the Diehl web server).
SEE ALSO
daicctl(1)
BUGS
The driver is not yet finished.
BSD
January 30, 1998 BSD