Changing single path NIC to a teamed connection in same subnet
Dear all,
I have a remote CentOS7 server that has two network cards. Each card has four ports and port one of card one was defined with the IP address assigned to the server. So far, so good and it's been working for over a year. We have now got cables sorted out so there are four paths available (two from each card, via two switches) to give us resilience. After that, I have built a logical teamed device with the three new paths and it's all working just fine until I try to turn off the old un-teamed/single path eno1. I think it's all down to routing and I'm stuck.
Output from ip add show (removed unused ports for clarity):-
Code:
2: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether b8:83:13:55:10:e0 brd ff:ff:ff:ff:ff:ff
inet 10.102.16.11/24 brd 10.102.16.255 scope global noprefixroute eno1
valid_lft forever preferred_lft forever
3: eno2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master team0 state UP group default qlen 1000
link/ether 98:f2:b3:1d:3e:04 brd ff:ff:ff:ff:ff:ff
6: eno5: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master team0 state UP group default qlen 1000
link/ether 98:f2:b3:1d:3e:04 brd ff:ff:ff:ff:ff:ff
7: eno6: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master team0 state UP group default qlen 1000
link/ether 98:f2:b3:1d:3e:04 brd ff:ff:ff:ff:ff:ff
22: team0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 98:f2:b3:1d:3e:04 brd ff:ff:ff:ff:ff:ff
inet 10.102.16.13/24 brd 10.102.16.255 scope global noprefixroute team0
valid_lft forever preferred_lft forever
All seems well and I have changed the DNS to refer to the new IP address for the team0 device. I can SSH to the new IP address and verify with netstat that I am connected to the new IP. Output from netstat -nr and route -n:-
Code:
# netstat -nr
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
0.0.0.0 10.102.16.254 0.0.0.0 UG 0 0 0 eno1
0.0.0.0 10.102.16.254 0.0.0.0 UG 0 0 0 team0
10.102.16.0 0.0.0.0 255.255.255.0 U 0 0 0 eno1
10.102.16.0 0.0.0.0 255.255.255.0 U 0 0 0 team0
# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 10.102.16.254 0.0.0.0 UG 0 0 0 eno1
0.0.0.0 10.102.16.254 0.0.0.0 UG 350 0 0 team0
10.102.16.0 0.0.0.0 255.255.255.0 U 100 0 0 eno1
10.102.16.0 0.0.0.0 255.255.255.0 U 350 0 0 team0
#
If I try to disable eno1 I get no network response until I turn it back on again via the console. It's the same it I delete the default route with route delete default gw 10.102.16.254 dev eno1
I just don't get it. There appears (to me) to be a valid route from device team0 so what am I missing?
I do see this oddity though:-
Code:
# arp -a
? (10.102.16.254) at <incomplete> on team0
? (10.102.16.254) at 00:22:bd:fa:09:ff [ether] on eno1
For completeness, my server reports the below:-
Code:
# uname -a
Linux my_host 3.10.0-957.27.2.el7.x86_64 #1 SMP Mon Jul 29 17:46:05 UTC 2019 x86_64 x86_64 x86_64 GNU/Linux
After I retire eno1 as a discreet connection, it will be added into the team to give the proper resilience.
I am quite expecting to be shown that I am a fool. I'd prefer that than being left hanging.
I have an OpenBSD 3.7 firewall with five network interfaces on it, one of which is connected to the Internet. I'd like to use the remaining four interfaces as a network switch for a single internal subnet. The main problem I have is that the DHCP daemon doesn't like multiple interfaces matching... (0 Replies)
I understand how to change the ip address permanently however, I need to also make a permanent change to the subnet mask. How would I accomplish this. (5 Replies)
Hi,
My project needs to migrate the existing Subnet (255.255.255.0) to a new subnet and change the ipaddresses (currently C class). How can I do that. I need some information.
John (0 Replies)
Hi,
I have a task to edit the subnet mask in almost 100+ solaris servers.Few of the servers are configured with IPMP.There will be no change of IP address or default gateway.If its a single IP we can bring NIC down,change the subnet mask in /etc/netmasks,then bring the NIC back to normal.But... (3 Replies)
I am new to this forum so please bare with me. I did search for this answer prior to posting but no luck.
Running an AIX NIM Master at 5.3TL9SP4, with about 100 clients. The subnet of one of the networks defined in the NIM env has changed. When I go to Manage Networks, Change/Show... (0 Replies)
Hello,
can anyone help me with the command to change the subnet mask on solaris 10? The mask is currently 255.255.255.255 I will like to change it to 255.255.2555.0.
Thank you (5 Replies)
I have a Solaris 11 machine with 2 network cables attached. The first one is the default route and is working okay. I am trying to activate the second on another subnet, but am sure missing something.
The first one is on 10.30.128. and with it everything works fine,
but when I try to add the... (0 Replies)
posted this on the other sub-forum
https://www.unix.com/unix-for-dummies-questions-and-answers/246504-solaris-11-2nd-nic-different-subnet.html
apologies if linking is not appropriate
Thanks for your help. (0 Replies)
Hi Guys,
Our lpars is currently running on 2 different vlans (20, 30). Now we have a requirement that vlan 30 needs to be change to vlan 31 at the same subnet. I'm not sure on what is the best approach for this or what change is involve on the AIX side.
This is our setup.
Network switch -... (5 Replies)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)