09-07-2019
Thanks for the update.
If a NIC suddenly fails, and no admin did something to your system or to the LAN switch then the next idea is hardware.
The IPMP concept is quite different from the port aggregation concept.
Does the latter exist in Solaris 9 at all? In the early days you had to purchase SunTrunking software.
These 2 Users Gave Thanks to MadeInGermany For This Post:
9 More Discussions You Might Find Interesting
1. Solaris
Hello All,
I work for a Health care company at a local trauma hospital. I maintain a Picture Archiving and Communication System (PAC's). Basically, any medical images (X-Ray, CT, MRI, Mammo, etc) are stored digitally on the servers for viewing and dictation from diagnostic stations. I took over... (10 Replies)
Discussion started by: mainegeek
10 Replies
2. Solaris
Does Veritas Cluster work with IPMP on Solaris 10?
If anyone has set it up do you have a doc or tips?
I have heard several different statements ranging from , not working at all to Yes it works! Great How?
* Test and Base IPs????
* configure the MultiNICB agent ?
I can give details... (1 Reply)
Discussion started by: dfezz1
1 Replies
3. Solaris
A problem happened with me, I was configuring IP for two network interfaces, and when I rebooted the system, everything is working but after like 3 or 5 minutes it will tell me that the whole IPMP group has failed !
I tried to troubleshoot, so I found that the gateway is not reachable..so I... (4 Replies)
Discussion started by: Sun Fire
4 Replies
4. Solaris
Hi friends ,
can anyone provide me the complete steps to configure IPMP in solaris 9 or 10 provided i have two NIC card ?
regards
jagan (4 Replies)
Discussion started by: jaganblore
4 Replies
5. Solaris
Can any one please explain me the concept behind IPMP in solaris clustering.Basic explanation would be really appreciated...
Thanks in Advance
vks (2 Replies)
Discussion started by: vks47
2 Replies
6. Solaris
All.
I am trying to create a 10 branded zone on a Sol 11.1 T5. The Global is using IPMP...so aggregating is out of the question. Has anyone successfully created a branded zone with IPMP? If they have can you please show me the steps you took to get this to run.
Thanks (4 Replies)
Discussion started by: aeroforce
4 Replies
7. Solaris
hi all,
i start with solaris 11 and i am disapointed by the change on ip managing.
i want to set a ipmp over tow aggregate but i dont find any doc and i am lost with the new commande
switch1
net0 aggregate1 |
net1 aggregate1 |-----|
|... (1 Reply)
Discussion started by: sylvain
1 Replies
8. Solaris
Hi all,
I been reading examples of how to setup IPMP and how it differs from Etherchannel. However, i am still unsure of how it really works and i hope gurus here can shed some light on the questions I have below while i will lab it up for my own test ->
q1) for IPMP, there is no such thing... (23 Replies)
Discussion started by: javanoob
23 Replies
9. Solaris
Hi all,
Just a few questions ->
Is an "OFFLINE" interface going back to "ONLINE" consider as a failback by IPMP ?
I have "FAILBACK=no" in my /etc/default/mpathd; however when i do the following
(igb0 and igb7 are in the same ipmp link based group)
q1) why does "if_mpadm -r igb7" cause... (0 Replies)
Discussion started by: javanoob
0 Replies
LEARN ABOUT DEBIAN
arpspoof
ARPSPOOF(8) System Manager's Manual ARPSPOOF(8)
NAME
arpspoof - intercept packets on a switched LAN
SYNOPSIS
arpspoof [-i interface] [-c own|host|both] [-t target] [-r] host
DESCRIPTION
arpspoof redirects packets from a target host (or all hosts) on the LAN intended for another host on the LAN by forging ARP replies. This
is an extremely effective way of sniffing traffic on a switch.
Kernel IP forwarding (or a userland program which accomplishes the same, e.g. fragrouter(8)) must be turned on ahead of time.
OPTIONS
-i interface
Specify the interface to use.
-c own|host|both
Specify which hardware address t use when restoring the arp configuration; while cleaning up, packets can be send with the own
address as well as with the address of the host. Sending packets with a fake hw address can disrupt connectivity with certain
switch/ap/bridge configurations, however it works more reliably than using the own address, which is the default way arpspoof cleans
up afterwards.
-t target
Specify a particular host to ARP poison (if not specified, all hosts on the LAN). Repeat to specify multiple hosts.
-r Poison both hosts (host and target) to capture traffic in both directions. (only valid in conjuntion with -t)
host Specify the host you wish to intercept packets for (usually the local gateway).
SEE ALSO
dsniff(8), fragrouter(8)
AUTHOR
Dug Song <dugsong@monkey.org>
ARPSPOOF(8)