09-05-2019
How to finish expanding a zfs filesystem?
I have a esxi 6.7 server running a Solaris 10 x86 vm (actually a bunch of them). The VM uses zfs for the pools (of course). I expand the underlying ESX logical disk, for example from 50GB to 100gb, then I set autoexpand=on <pool> that belongs to the esx logical disk.
what am i missing to finalize the expansion of the filesystem?
zpool list <pool> shows the expanded size of the disk, but the when mounted, the zfs filesystem is not expanded.
Do I need to set the reservation size for the filesystem? Right now, by default there is no reservations on the filesystem.
7 More Discussions You Might Find Interesting
1. Solaris
I created a zpool and two ZFS volumes in OpenSolaris. I would like both ZFS volumes to be exportable. However, I don't know how to set that up.
These are the steps I did:
1) Create the zpool using raidz1 across five disks.
I have six disks and created a zpool across 5 of them. c4t0d0... (3 Replies)
Discussion started by: sqa777
3 Replies
2. Solaris
I created a zpool and zfs filesystem in OpenSolaris. I made two NFS mount points:
> zpool history
History for 'raidpool':
2009-01-15.17:12:48 zpool create -f raidpool raidz1 c4t1d0 c4t2d0 c4t3d0 c4t4d0 c4t5d0
2009-01-15.17:15:54 zfs create -o mountpoint=/vol01 -o sharenfs=on -o... (0 Replies)
Discussion started by: sqa777
0 Replies
3. Solaris
Hey all,
I have a machine with 16 drive slots. Two of the drives have a ZFS mirror of the operating system, the other 14 contain the storage raidz.
So, after installing Opensolaris on the OS drives, how can I remount the storage raid?
TIA (11 Replies)
Discussion started by: PatrickBaer
11 Replies
4. Filesystems, Disks and Memory
Hi Folks,
Looking for info here more than any actual HowTo, does anyone know if there is an actual way of converting a Veritas or UFS filesystem to ZFS leaving the resident data intact.
All that I have been able to find, including the commercial products seem to require the FS backed up from... (1 Reply)
Discussion started by: gull04
1 Replies
5. Solaris
Hi guys!
How come ZFS is said to be not just a filesystem but a hybrid filesystem and also a volume manager? Please explain.
I will appreciate your replies. Hope you can help me figure this out.
Thanks in advance! (1 Reply)
Discussion started by: Klyde
1 Replies
6. Solaris
Hi,
Recently we have new server T5 Oracle. We set up it for our database. For out database files we set one zfs filesystem. When i use iostat -xc the output as below. As you see the value for vdc4 is quite high.
extended device statistics cpu
device ... (32 Replies)
Discussion started by: tharmendran
32 Replies
7. Solaris
Hello,
Need to ask the question regarding extending the zfs storage file system.
currently after using the command, df -kh
u01-data-pool/data 600G 552 48G 93% /data
/data are only 48 gb remaining and it has occupied 93% for total storage.
zpool u01-data-pool has more then 200 gb... (14 Replies)
Discussion started by: shahzad53
14 Replies
LEARN ABOUT DEBIAN
dpm-modifyfs
DPM-MODIFYFS(1) DPM Administrator Commands DPM-MODIFYFS(1)
NAME
dpm-modifyfs - modify the parameters of a disk pool filesystem
SYNOPSIS
dpm-modifyfs --server fs_server --fs fs_name [ --st status ] [ --weight weight ] [ --help ]
DESCRIPTION
dpm-modifyfs modifies the parameters of a disk pool filesystem.
This command requires ADMIN privilege.
OPTIONS
server specifies the host name of the disk server where this filesystem is mounted.
fs specifies the mount point of the dedicated filesystem.
status New status of this filesystem. It can be set to 0 (enabled read/write) or DISABLED or RDONLY. This can be either alphanumeric or
the corresponding numeric value.
weight specifies the weight of the filesystem. This is used during the filesystem selection. The value must be positive. It is recommended
to use a value lower than 10.
EXAMPLE
dpm-modifyfs --server sehost --fs /data --st RDONLY
EXIT STATUS
This program returns 0 if the operation was successful or >0 if the operation failed.
SEE ALSO
dpm(1), dpm_modifyfs(3)
LCG
$Date$ DPM-MODIFYFS(1)