Greetings.
I am struggling with a shell script to make my life simpler, with a number of practical ways in which it could be used. I want to take a standard text file, and pull the 'n'th word from each line such as the first word from a text file.
I'm struggling to see how each line can be... (5 Replies)
Hey All,
On commad promt of a shell..
How can we move our cursor word by word.
Like Ctrl+A takes to the starting of the command...
Any shortcut like that..?
Thanks
pbsrinivas (1 Reply)
I have a file from which the Header and the Trailer lines need to be removed. They are confirmed to be the first and the last lines in the file.
I have tried a few commands, but not successful yet. It needs to be implemented urgently, hence any help is greatly appreciated.
Raghu
----------... (1 Reply)
Hi All,
If my file is:
Wed Sep 9 22:45:14 EDT 2009
sftp> sftp> sftp> sftp> sftp> sftp> sftp> sftp> sftp> sftp> sftp> sftp> sftp>
This is log file generated from transfer...
sftp> sftp> sftp> sftp> Files placed properly....
sftp> sftp> sftp>
How can I remove "sftp>" word from this... (4 Replies)
Hi Guys,
I have a file like this:
wwwe 1 ioie ewew yyy uuu 88
erehrlk 4 ihoiwhe lkjhassad lkhsad yyy mmm 45
jhash lhasdhs lkhsdkjsn ouiyrshroi oihoihswodnw oiyhewe yyy ggg 77
I want to remove everything after "yyy" and including "yyy" from each line in the file.
So I want:... (2 Replies)
Hi Guys, :p
I have a file like this:
2010-04-25 00:00:30,095 INFO - ]- start process U100M4
2010-04-25 00:00:30,096 DEBUG - ] -- call EJB
2010-04-25 00:00:30,709 INFO - - end processU100M4
2010-04-25 00:00:30,710 DEBUG - got message=Sorry
I want to out put format.
2010-04-25... (5 Replies)
Hello All,
I am running a command find . -name amp.cfg | cut -c 3- which gives me output something like below
rel/prod/amp.cfg
rel/fld/amp.cfg
deb/detail/amp.cfg
deb/err/amp.cfg I want to remove trailing "/amp.cfg" so that i should get output something like... (7 Replies)
Hi All,
Hope you guys had a wonderful weekend
I have a scenario where in which I have to read a file line by line
and check for few words before redirecting to a file
I have searched the forum but,either those answers dint work (perhaps because of my wrong under standing of how IFS... (6 Replies)
I have a file: file.txt, which contains the following data in it.
This is a file, my name is Karl, what is this process, karl is karl junior, file is a test file, file's name is file.txt
My name is not Karl, my name is Karl Joey
What is your name?
Do you know your name and... (3 Replies)
hello.
How to remove first word from line. The line may or may not start with blank.
NEW_PARAM1=$(magic-command " -t --protocol=TCP -P 12345-u root -h localhost ")
NEW_PARAM2=$(magic-command "-t --protocol=TCP -P 12345 -u root -h localhost ")
I want NEW_PARAM1 equal to NEW_PARAM2 equal ... (2 Replies)
Discussion started by: jcdole
2 Replies
LEARN ABOUT DEBIAN
catcodec
CATCODEC(1) BSD General Commands Manual CATCODEC(1)NAME
catcodec -- An open source tool to decode/encode the sample catalogue for OpenTTD
SYNOPSIS
catcodec [-d sample_file] [-e sample_file]
DESCRIPTION
catcodec decodes and encodes sample catalogues for OpenTTD. These sample catalogues are not much more than some meta-data (description and
file name) and raw PCM data.
Decoding a sample catalogue, e.g. sample.cat, results in a sample.sfo that contains the file names and descriptions of the samples and all
samples with the file name as specified in the catalogue.
Encoding a sample catalogue, e.g. sample.cat, reads sample.sfo for the file names and descriptions. It will then load the samples described
in sample.sfo and encodes these into sample.cat.
Generally speaking encoding a file and then decoding it results in the same file. Decoding of the original, Transport Tycoon Deluxe, sample
format will force the output to be 11025 Hz, 8 bits mono because the meta-data of some of the samples is incorrect or even missing.
Only PCM WAVE files with only the format and data chunks are supported. Any other formats need to be converted into this. Furthermore only
11025 Hz, 22050 Hz and 44100 Hz with 8 or 16 bits per sample single channel PCM WAVE files are supported.
OPTIONS -d sample_file Decode the given sample catalogue into its components. The sample_file must have the extension '.cat'. For the output meta-
data file the '.cat' is replaced with '.sfo'. The actual samples, in PCM WAVE format, are extracted into files using the file
names, including extension, as described in the catalogue or meta-data file.
If any of the files already exists a backup is made, by adding '.bak', overwriting the existing backup.
-e sample_file Encode the components for the given sample file into a sample catalogue. The sample_file must have the extension '.cat'. For
the input meta-data file the '.cat' is replaced with '.sfo'. The actual samples, in PCM WAVE format, are read from files
using the file names, including extension, as described in the meta-data file.
If the sample_file already exists a backup is made, by adding '.bak', overwriting the existing backup.
SEE ALSO openttd(1) the game that uses these sample catalogues.
AUTHORS
Remko Bijker <rubidium@openttd.org>
November 05, 2009
08-22-2019
