Bash script, find the next closed (not in use) port from some port range. Post: 303036756

9 More Discussions You Might Find Interesting

1. SCO

tcp port always closed in inetd

sco unix 5.0.x, several weeks ago, I add a telnet-like service in inetd.conf, it runs well for 100 network terminals. But nowdays, the terminals can connect to server successfully after booting machine, but several hours later, can not connect. "netstat -p tcp -a" can NOT find the port in...

2. AIX

TCP/UDP port range for default AIX NFS?

May I know what is the TCP/UCP port range for any default AIX NFS? Based on rpcinfo -p, I got the following output: program vers proto port service 100000 4 udp 111 portmapper 100000 3 udp 111 portmapper 100000 2 udp 111 portmapper 100000 4 ...

3. Solaris

How to enable Serial port on ILOM, when Network Port is enabled in parallel

Hi Everyone, In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected...

4. Shell Programming and Scripting

Block local and remote port with iptables - Script BASH

Hello I'm beginner in the linux scripting and i would like to get help. I want to create a script that can block one or more Port even see all the TCP port. The ports must be blocked even when starting my machine. Of course requires a second script which will allow the ports that you want to...

5. AIX

Allow port range using IPsec?

Hi Guys, Please could you tell me if it is possible to have a single rule/filter to allow a certain port range instead of a separate rule for each port? I'm sure it must be possible but I am unable to find the syntax. Thanks Chris

6. UNIX for Dummies Questions & Answers

iptables to block port 25 only to a certain range

I want to limit all *outbound* traffic on eth0 (or all *.*) on port 25 to a specific (allowed) range... I.E. 192.168.1.5 (local ip) tries to connect to 1.2.3.4:25 (outside real world ip) It can proceed because 1.2.3.0/24 is the allowed range Now, 192.168.1.5 (local ip) tries to connect to...

7. Red Hat

Which is the effective ephemeral port range in Linux 2.6 for this set up?

In my Linux system ephemeral port range is showing different ranges as follows $ cat /proc/sys/net/ipv4/ip_local_port_range 32768 61000  cat /etc/sysctl.conf | grep net.ipv4.ip_local_port_range net.ipv4.ip_local_port_range = 9000 65500 Which will be the effective ephemeral port...

8. Solaris

How to find port number wwn of particular port on dual port HBA,?

please find the below o/p for your reference bash-3.00# fcinfo hba-port HBA Port WWN: 21000024ff295a34 OS Device Name: /dev/cfg/c2 Manufacturer: QLogic Corp. Model: 375-3356-02 Firmware Version: 05.03.02 FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;...

9. AIX

Forcing named 9 to use a fixed ephemeral port range

I'll start with I'm not an AIX expert, I inherited a lot of AIX servers to maintain. My problem is on AIX 7.1 TL4 SP4 environments. I'm running named as a DNS forwarder only to internal DNS servers. These AIX servers have a customized UDP ephemeral port range to avoid conflicting with the...

LEARN ABOUT NETBSD

zfgrep

ZGREP(1)						    BSD General Commands Manual 						  ZGREP(1)

NAME

     zgrep, zegrep, zfgrep -- print lines matching a pattern in gzip-compressed files

SYNOPSIS

     zgrep [grep-flags] [--] pattern [files ...]

     zegrep [grep-flags] [--] pattern [file ...]

     zfgrep [grep-flags] [--] pattern [file ...]

DESCRIPTION

     zgrep runs grep(1) on files or stdin, if no files argument is given, after decompressing them with zcat(1).

     The grep-flags and pattern arguments are passed on to grep(1).  If an -e flag is found in the grep-flags, zgrep will not look for a pattern
     argument.

     zegrep calls egrep(1), while zfgrep calls fgrep(1).

EXIT STATUS

     In case of missing arguments or missing pattern, 1 will be returned, otherwise 0.

SEE ALSO

     egrep(1), fgrep(1), grep(1), gzip(1), zcat(1)

AUTHORS

     Thomas Klausner <wiz@NetBSD.org>

BSD
								 December 28, 2003							       BSD