- I can see the new drive, with the correct serial #
Code:
lscfg -v -l pdisk18
pdisk18 U5886.001.P15R082-P1-D3 Physical SAS Disk Drive
Manufacturer................IBM
Machine Type and Model......ST3300656SS
FRU Number..................10N7208
ROS Level and ID............45363043
Serial Number...............3QP2CYYW
However, when trying to Create an Array Candidate pdisk and Format to 528 Byte Sectors it doesn't show up.
==
Create an Array Candidate pdisk and Format to 528 Byte Sectors
│ pdisk22 00000600 Active Array Candidate 283.8GB │
│ pdisk23 00000700 Active Array Candidate 283.8GB │
│ pdisk24 00000800 Active Array Candidate 283.8GB │
│ pdisk25 00000900 Active Array Candidate 283.8GB
===
Neither in the array conf:
sissas3 FFFFFFFF Primary PCI-X266 Ext Tri-x4 3Gb SAS RAID Adapter
sissas2 00000000 AWC linked Redundant cache protection for sissas3
hdisk9 00FF0000 Degraded RAID 10 Array 851.4GB
pdisk21 00000500 Active Array Member 283.8GB
pdisk27 00000B00 Active Array Member 283.8GB
pdisk17 00000100 Active Array Member 283.8GB
pdisk20 00000400 Active Array Member 283.8GB
pdisk16 00000000 Active Array Member 283.8GB
pdisk19 00000300 Active Array Member 283.8GB
pdisk24 00000800 Active Array Candidate 283.8GB
pdisk22 00000600 Active Array Candidate 283.8GB
pdisk23 00000700 Active Array Candidate 283.8GB
pdisk25 00000900 Active Array Candidate 283.8GB
pdisk26 00000A00 Active Hot Spare 283.8GB
pdisk18 00000200 Missing Disk 283.8GB
Dear Friends,
I need to configure T5240 with Internal SAS RAID HBA(SG-XPCIESAS-R-INT-Z).. T5240 uses 8 hard disks... From the documents of RAID card I have found that I need to create a jump start server to include three packages SUNWaac, StorMan, SUNWgccruntime if Im using solaris10 5/08...
... (5 Replies)
We have a dual-controller StorEdge 3320 disk array with 5 disks (each 320 MB). Four disks have been set up in a RAID-5 configuration with the remaining disk acting as a hot spare. There is a single logical drive which has been partitioned into 3 slices.
The disk array is to be simultaneously... (14 Replies)
May I know how can I add a new SSA pdisk into array and become usable hdisk? I have inserted a 36GB SSA disk into enclosure and done the "cfgmgr" and I can see it already been regconized as pdisk47.
I would like to make it a system disk in order for me to add to my volume group. Please let me... (3 Replies)
Hi,
I`m on SunFire480R with Solaris 10. Disk in rootdg group failed, so it was replaced. However, I cannot make Veritas initalise the replaced disk:
# vxdctl enable
# vxdisk list c1t0d0s2
Device: c1t0d0s2
devicetag: c1t0d0
type: auto
flags: online error private autoconfig... (1 Reply)
Hi,
Is there an easy way to find the disk-type from the command line or with another api ? sdparm works for SAS but not for SATA, hdparm works for SATA but not SAS.
Thanks (1 Reply)
Hi,
a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced.
here is how I did that.
1) created identical partition table on the new disk.
2) attached the mirrors using md commands.
The whole procedure is given... (5 Replies)
Hi,
a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced.
here is how I did that.
1) created identical partition table on the new disk.
2) attached the mirrors using md commands.
The whole procedure is given below:... (2 Replies)
I need to add a VMware virtual disk to the 99-oracle-asmdevices.rules file but the OS is not assigning a WWID to the disk. It has been fdisk'd and a single partition created.
What TAG inside the file needs to be added? the Program scsi-id does not work for some reason. latest patches... (0 Replies)
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (1 Reply)
Hello,
I would like to check how many SAS disks and its size per disk for the whole power system. As per my understanding, if we assign the SAS controller to LPAR, then we can see the disk in lpar smitty command.
How can we check from the Power machine(physical ones) as well? I think the... (5 Replies)
Discussion started by: Phat
5 Replies
LEARN ABOUT HPUX
proto
proto(4) Kernel Interfaces Manual proto(4)NAME
proto - prototype job file for at
SYNOPSIS DESCRIPTION
When a job is submitted to or the job is constructed as a POSIX shell script (see at(1)). The job file is created in as follows:
o creates a header describing the job as an job or a job. jobs submitted to all queues other than queue are listed as jobs. The header
is:
for an job, or
for a job.
o A set of POSIX shell commands is added to make the environment (see environ(5)) for the job the same as the current environment.
o then copies text from the prototype file to the job file, except for special variables that are replaced by other text:
Replaced by the current working directory.
Replaced by the current file size limit (see
ulimit(2)).
Replaced by the current umask (see
umask(2)).
Replaced by the time at which the job should be run,
expressed as seconds since January 1, 1970, 00:00 Coordinated Universal Time, preceded by a colon.
Replaced by text read by
from the standard input (that is, the commands provided to to be run in the job).
o When a job is submitted to queue queue, uses the file as the prototype file if it exists. Otherwise, it uses the file
EXAMPLES
The following file creates commands to change the current directory, file size limit, and umask in the job to their respective values as
they existed when was originally run. These commands are inserted before the commands in the job:
SEE ALSO at(1), queuedefs(4).
STANDARDS CONFORMANCE proto(4)