06-13-2019
trevian,
You'll need to be able to get a console that you are able to use to get the wwn's from the adapters. The problem that I see, and posted about above, is that your PCI bus appears to have a fault. So it is very likely AIX won't be able to see your adapters to get the zoning information. IBM or someone with intimate knowledge of AIX/Power error codes could really decode the full errpt to know what else needs to be replaced on this frame.
10 More Discussions You Might Find Interesting
1. IP Networking
Im newest in unix,
Please, give me solution for installing lan adapter if driver not found in the list of ethernet drivers
ihave unix driver in a dos diskete
please give me the other solution
and tell me where the domain of unix class online, so ican read from it.
Thank's very much (3 Replies)
Discussion started by: ade_muhdiat
3 Replies
2. Solaris
Hi. I need to find a simple SCSI adapter card for a Sun Ultra 5 workstation. I don't need the type w/ ethernet attached (e.g. X1032) as I already have ethernet onboard & they are more spendy.
I know Adaptec is out, but what unit would work? I am attaching an external SCSI tape unit to this... (4 Replies)
Discussion started by: Plain Person
4 Replies
3. Solaris
Hi everyone, it's me the Solaris novice once again. Here's my situation.
- I bought a Sun Ultra 10 Creator 3D Workstation and Sony 19" SVGA Monitor package deal.
- The system has the Creator 3D Video Adapter installed but I could not use it because the adapter has a 13w3 connection and my... (5 Replies)
Discussion started by: jbarbuto
5 Replies
4. HP-UX
Hi ,
Hi what is an adapter?what is its use ?
How to log into a tibco server from unix home directory. (1 Reply)
Discussion started by: megh
1 Replies
5. UNIX for Dummies Questions & Answers
Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean?
- It has to run on all network adapters
- It has to be as simple as it can be
- It has to run on all linux distributions (or at least most of them)
- It does not have to run a network... (4 Replies)
Discussion started by: Chrisdot
4 Replies
6. SCO
I inserted a PCI Realtek RTL8139 network adapter on a PC running SCO Openserver 5.0.6.
I successfully loaded drivers and I'm trying to install the card with netconfig command, unfortunately without success.
Here are the steps I follow to install the card:
I run netconfig, from menu 'hardware'... (2 Replies)
Discussion started by: kampus
2 Replies
7. Hardware
I need to connect 80pin SCA Ultra320 SCSI hdd to 68pin.
There are rumors that some bad "passive" adapters with problematic termination can fry the HDD. The adapter we got is Assmann ABSCA-2. Hard drive is 'Fujitsu MAW3073NC'
Do we need to set any jumpers before turning it on?
We already had... (0 Replies)
Discussion started by: orange47
0 Replies
8. AIX
Hello,
Runing VIO and couple lpars on POWER blade.
I want to dedicate graphics adapter(ati0) to one lpar. Is that possible ?
I tried to do that using IVM (I/O Adapter Management->View/Modify Physical Adapters->Modify partition assignment):
Failed to remove adapter U78A6.001.WIH4088-P2-C8... (1 Reply)
Discussion started by: vilius
1 Replies
9. AIX
Hi,
I want to change from vscsi to npiv. Is it possible to use both on the same adapter, so we can change the systems one by one, or must we place a second FC adapter in the VIO servers?
Thanks,
Ronald (2 Replies)
Discussion started by: ronaldm60
2 Replies
10. Red Hat
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Discussion started by: chidhu.anu
4 Replies
LEARN ABOUT CENTOS
iprupdate
IPRUPDATE(8) System Manager's Manual IPRUPDATE(8)
NAME
iprupdate - IBM Power RAID adapter/device microcode update utility
SYNOPSIS
iprupdate
iprupdate --debug --check_only --daemon --use-polling --use-uevents
DESCRIPTION
iprupdate is used to update the microcode on IBM storage adapters and the disk units attached to them to a minimum supported level. It can
be run at any time while the ipr device driver is loaded. The utility will check the microcode revision level of each storage adapter/disk
unit on the system and compare it to the microcode revision level that is installed in /etc/microcode, /usr/lib/microcode, and
/lib/firmware. If the microcode level on the adapter/device is below the minimum supported level and the level of the latest image is
newer, the microcode will be updated to the latest level available. It is desired that this be called in the boot process.
OPTIONS
--version
Print the version number of iprupdate
--debug
Enable additional error logging. Enabling this will result in additional errors logging to /var/log/messages.
--check_only
Check if any adapters or disk units are below their minimum supported level.
--daemon
Run as a daemon to handle adapters and devices being hotplugged.
--use-polling
Do not use netlink/uevent notification, but rather poll for adapter and device configuration changes.
--use-uevents
Use netlink/uevent notification rather than polling for adapter and device configuration changes. If not specified, polling will be
used until the first uevent notification appears, then netlink will be used.
AUTHOR
Brian King (brking@us.ibm.com)
February 2005 IPRUPDATE(8)