06-13-2019
trevian,
You'll need to be able to get a console that you are able to use to get the wwn's from the adapters. The problem that I see, and posted about above, is that your PCI bus appears to have a fault. So it is very likely AIX won't be able to see your adapters to get the zoning information. IBM or someone with intimate knowledge of AIX/Power error codes could really decode the full errpt to know what else needs to be replaced on this frame.
10 More Discussions You Might Find Interesting
1. IP Networking
Im newest in unix,
Please, give me solution for installing lan adapter if driver not found in the list of ethernet drivers
ihave unix driver in a dos diskete
please give me the other solution
and tell me where the domain of unix class online, so ican read from it.
Thank's very much (3 Replies)
Discussion started by: ade_muhdiat
3 Replies
2. Solaris
Hi. I need to find a simple SCSI adapter card for a Sun Ultra 5 workstation. I don't need the type w/ ethernet attached (e.g. X1032) as I already have ethernet onboard & they are more spendy.
I know Adaptec is out, but what unit would work? I am attaching an external SCSI tape unit to this... (4 Replies)
Discussion started by: Plain Person
4 Replies
3. Solaris
Hi everyone, it's me the Solaris novice once again. Here's my situation.
- I bought a Sun Ultra 10 Creator 3D Workstation and Sony 19" SVGA Monitor package deal.
- The system has the Creator 3D Video Adapter installed but I could not use it because the adapter has a 13w3 connection and my... (5 Replies)
Discussion started by: jbarbuto
5 Replies
4. HP-UX
Hi ,
Hi what is an adapter?what is its use ?
How to log into a tibco server from unix home directory. (1 Reply)
Discussion started by: megh
1 Replies
5. UNIX for Dummies Questions & Answers
Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean?
- It has to run on all network adapters
- It has to be as simple as it can be
- It has to run on all linux distributions (or at least most of them)
- It does not have to run a network... (4 Replies)
Discussion started by: Chrisdot
4 Replies
6. SCO
I inserted a PCI Realtek RTL8139 network adapter on a PC running SCO Openserver 5.0.6.
I successfully loaded drivers and I'm trying to install the card with netconfig command, unfortunately without success.
Here are the steps I follow to install the card:
I run netconfig, from menu 'hardware'... (2 Replies)
Discussion started by: kampus
2 Replies
7. Hardware
I need to connect 80pin SCA Ultra320 SCSI hdd to 68pin.
There are rumors that some bad "passive" adapters with problematic termination can fry the HDD. The adapter we got is Assmann ABSCA-2. Hard drive is 'Fujitsu MAW3073NC'
Do we need to set any jumpers before turning it on?
We already had... (0 Replies)
Discussion started by: orange47
0 Replies
8. AIX
Hello,
Runing VIO and couple lpars on POWER blade.
I want to dedicate graphics adapter(ati0) to one lpar. Is that possible ?
I tried to do that using IVM (I/O Adapter Management->View/Modify Physical Adapters->Modify partition assignment):
Failed to remove adapter U78A6.001.WIH4088-P2-C8... (1 Reply)
Discussion started by: vilius
1 Replies
9. AIX
Hi,
I want to change from vscsi to npiv. Is it possible to use both on the same adapter, so we can change the systems one by one, or must we place a second FC adapter in the VIO servers?
Thanks,
Ronald (2 Replies)
Discussion started by: ronaldm60
2 Replies
10. Red Hat
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Discussion started by: chidhu.anu
4 Replies
CP(4) BSD/i386 Kernel Interfaces Manual CP(4)
NAME
cp -- driver for synchronous Cronyx Tau-PCI WAN adapters
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device cp
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_cp_load="YES"
Additional options:
device sppp
options NETGRAPH
options NETGRAPH_CRONYX
DESCRIPTION
The cp driver needs either sppp(4) or netgraph(4). Which one to use is determined by the NETGRAPH_CRONYX option. If this option is present
in your kernel configuration file, the cp driver will be compiled with netgraph(4) support. Otherwise, it will be compiled with sppp(4) sup-
port.
Refer to sconfig(8) for information about the cp adapter configuration.
HARDWARE
The cp driver supports the following models of Tau-PCI WAN adapters:
Cronyx Tau-PCI V.35 and RS-232 interfaces
Cronyx Tau-PCI/R RS-530(RS-449) and X.21 interfaces
Cronyx Tau-PCI-L one V.35 and RS-232 interface, low profile
Cronyx Tau-PCI-L/R one RS-530(RS-449) and X.21 interface, low profile
Cronyx Tau-PCI-E1 fractional E1 interfaces
Cronyx Tau-PCI-G703 unframed E1 interfaces
Cronyx Tau-PCI-2E1 fractional E1 and unframed E1 interfaces
Cronyx Tau-PCI-4E1 fractional E1 and unframed E1 interfaces
Cronyx Tau-PCI-E3 E3 interface
Cronyx Tau-PCI-T3 T3 interface
Cronyx Tau-PCI-STS1 STS-1 interface
SEE ALSO
ctau(4), cx(4), sppp(4), ifconfig(8), sconfig(8), spppcontrol(8)
HISTORY
The cp driver was added in FreeBSD 5.3 and FreeBSD 4.11. The cp driver for previous versions of FreeBSD is available from
http://www.cronyx.ru/.
BSD
July 16, 2005 BSD