AIX - NIC device explanation need Post: 303035910

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Dleting a Device in AIX 4.3

I need to delete a TTY in my AIX 4.3 system. I have tried using the smit but everytime I try it, there is a message telling me that the device is in use and cannot be changed. How do I take the device "offline", so to speak, so that I can edit the settings and/or delete it. V/R Djassi

2. UNIX for Dummies Questions & Answers

NIC and Device NO to Change

I am a beginer in unix . I would like to know what is the command in orser to change NIC and Device NO

3. AIX

AIX -How to find which NIC is on which PCI card

Hi All, How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v Any idea? Thanks.

4. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux...

5. AIX

Explanation of C Compiler for AIX

Hi, I have the following packages installed on my AIX server xlC.aix50.rte 10.1.0.2 COMMITTED XL C/C++ Runtime for AIX 5.3 xlC.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor xlC.msg.en_US.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor xlC.msg.en_US.rte 10.1.0.2 COMMITTED XL C/C++ Runtime xlC.rte...

6. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome....

7. AIX

AIX Frame: NIC port down

NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR. How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a...

8. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected...

9. UNIX for Beginners Questions & Answers

Configuring NIC device in Solaris 9 SPARC OS [QEMU]

I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only. ...

LEARN ABOUT FREEBSD

if_udav

UDAV(4) 						   BSD Kernel Interfaces Manual 						   UDAV(4)

NAME

     udav -- Davicom DM9601 USB Ethernet driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device ehci
	   device uhci
	   device ohci
	   device usb
	   device miibus
	   device udav

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   if_udav_load="YES"

HARDWARE

     The udav driver supports the following adapters:

     o	 Corega FEther USB-TXC
     o	 ShanTou ST268 USB NIC

DESCRIPTION

     The udav driver provides support for USB Ethernet adapters based on the Davicom DM9601 chipset.

     For more information on configuring this device, see ifconfig(8).

SEE ALSO

     altq(4), arp(4), miibus(4), netintro(4), ng_ether(4), usb(4), ifconfig(8)

     Davicom DM9601 data sheet, http://ptm2.cc.utu.fi/ftp/network/cards/DM9601/From_NET/DM9601-DS-P01-930914.pdf.

HISTORY

     The udav device driver first appeared in NetBSD 2.0.

AUTHORS

     The udav driver was written by Shingo WATANABE <nabe@nabechan.org>.

BSD
								   July 16, 2005							       BSD