05-26-2019
Why do you want two default gateways??
This User Gave Thanks to MadeInGermany For This Post:
9 More Discussions You Might Find Interesting
1. IP Networking
i'm a real unix newbie, setting up a network, with a router to router vpn connection with a remote site, all the win stuff is talking and pinging and all the stuff it should be doing (yeah and crashing too, lol) but no communication with the unix box, i think the problem is with my default... (3 Replies)
Discussion started by: smcg
3 Replies
2. AIX
Hi,
I have two interfaces on m AIX 5.3 box. One going to 192.168.1.x and it has a gateway of 192.168.1.1.
I configured the other gateway with 192.168.2.x and the default gateway as 192.168.2.1. But I can't get connectivity to the 192.168.2.1 network. Can someone help me out and let me know... (7 Replies)
Discussion started by: bbbngowc
7 Replies
3. HP-UX
where in configuration files can i modify default gateway in hp-ux11iv3 (5 Replies)
Discussion started by: h@foorsa.biz
5 Replies
4. Linux
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Discussion started by: mfondoum
0 Replies
5. Red Hat
Hi,
I have server that I change its network configuration from using DHCP to using static IP.
I have edited the file /etc/sysconfig/network-scripts/ifcfg-eth0
To:
BOOTPROTO=STATIC
IPADDR=xxx.xxx.xxx.xxx
NETMASK=255.255.255.0
GATEWAY=yyy.yyy.yyy.yyy
I did
/etc/init.d/network... (2 Replies)
Discussion started by: programAngel
2 Replies
6. Solaris
Hi Greetings...
I have an issue in connecting the zone from outside the network and it is because of default gateway. I can ping default gateway from inside the zone and not able to ping from global zone due to different VLAN issue. If i add two different gateways and restart network services,... (2 Replies)
Discussion started by: vvpotugunta
2 Replies
7. Red Hat
Hi..I have to change default gateway in my linux machine. Its OS is RHEL6.
I followed following steps.
1.run command ip route to check current default gateway
2.delete that gateway with command
route del default gw x.x.x.x eth2
3.Add new gatewy with command below
route add default gateway... (3 Replies)
Discussion started by: deljatt
3 Replies
8. AIX
hello
iv 2 AIX P720 machine aix 6.1 6100-02-03-0909 both , hacmp ver 6.1.0.0
both machine connect to the same switch. after networking fault , one of the machines lost his default gateway !!!
what can be the reason ?
thx (4 Replies)
Discussion started by: ariec
4 Replies
9. IP Networking
I am am using IPv6 IP's with an OS of Debian.
Is it possible to set a *static* default gateway w/o the router being connected? Will that gateway change when the router is connected?
TIA (0 Replies)
Discussion started by: Meow613
0 Replies
ping(8) System Manager's Manual ping(8)
Name
ping - send ICMP ECHO_REQUEST packets to network hosts
Syntax
/etc/ping [ options ] host [ datasize [ npackets ]]
Description
The DARPA Internet is a large and complex network of hardware connected together by gateways. The command utilizes the ICMP protocol's
mandatory ECHO_REQUEST datagram to elicit an ICMP ECHO_RESPONSE from a host or gateway. ECHO_REQUEST datagrams (pings) have an IP and ICMP
header, followed by a struct timeval, and then an arbitrary number of pad bytes used to fill out the packet. The length of the default
datagram 64 bytes, but this may be changed using the command-line option.
Typing ``ping host'' without any options will either report ``host is alive'' or ``no answer from host''. To get more statistics use the
-l option or one of the other options.
When using for fault isolation, it should first be run on the local host to verify that the local network interface is up and running.
Then, hosts and gateways further and further away should be pinged. The command with options sends one datagram per second and prints one
line of output for every ECHO_RESPONSE returned. No output is produced if there is no response. If an optional npackets is given, only
that number of requests is sent. Round-trip times and packet loss statistics are computed. When all responses have been received or the
program times out with npackets specified, or if the program is terminated with a SIGINT, a brief summary is displayed.
Options
-d Turns on SO_DEBUG flag on the socket.
-l Gives more statistics than if is used without options. Long output.
-r Bypasses the normal routing tables and sends directly to a host on an attached network. If the host is not on a directly-attached
network, an error is returned. This option can be used to ping a local host through an interface that has no route through it. For
example, after the interface was dropped by
-v Lists ICMP packets other than ECHO RESPONSE that are received. Verbose output.
Restrictions
This program is intended for use in network testing, measurement, and management. It should be used primarily for manual fault isolation.
Because of the load it could impose on the network, it is unwise to use during normal operations or from automated scripts.
See Also
netstat(1), ifconfig(8c)
ping(8)