Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different. After restarting the service, the default gateway is lost and the external network cannot be accessed. Do you know why?
The configuration file information is as follows:
i'm a real unix newbie, setting up a network, with a router to router vpn connection with a remote site, all the win stuff is talking and pinging and all the stuff it should be doing (yeah and crashing too, lol) but no communication with the unix box, i think the problem is with my default... (3 Replies)
Hi,
I have two interfaces on m AIX 5.3 box. One going to 192.168.1.x and it has a gateway of 192.168.1.1.
I configured the other gateway with 192.168.2.x and the default gateway as 192.168.2.1. But I can't get connectivity to the 192.168.2.1 network. Can someone help me out and let me know... (7 Replies)
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Hi,
I have server that I change its network configuration from using DHCP to using static IP.
I have edited the file /etc/sysconfig/network-scripts/ifcfg-eth0
To:
BOOTPROTO=STATIC
IPADDR=xxx.xxx.xxx.xxx
NETMASK=255.255.255.0
GATEWAY=yyy.yyy.yyy.yyy
I did
/etc/init.d/network... (2 Replies)
Hi Greetings...
I have an issue in connecting the zone from outside the network and it is because of default gateway. I can ping default gateway from inside the zone and not able to ping from global zone due to different VLAN issue. If i add two different gateways and restart network services,... (2 Replies)
Hi..I have to change default gateway in my linux machine. Its OS is RHEL6.
I followed following steps.
1.run command ip route to check current default gateway
2.delete that gateway with command
route del default gw x.x.x.x eth2
3.Add new gatewy with command below
route add default gateway... (3 Replies)
hello
iv 2 AIX P720 machine aix 6.1 6100-02-03-0909 both , hacmp ver 6.1.0.0
both machine connect to the same switch. after networking fault , one of the machines lost his default gateway !!!
what can be the reason ?
thx (4 Replies)
I am am using IPv6 IP's with an OS of Debian.
Is it possible to set a *static* default gateway w/o the router being connected? Will that gateway change when the router is connected?
TIA (0 Replies)
Discussion started by: Meow613
0 Replies
LEARN ABOUT FREEBSD
nos-tun
NOS-TUN(8) BSD System Manager's Manual NOS-TUN(8)NAME
nos-tun -- implement ``nos'' or ``ka9q'' style IP over IP tunnel
SYNOPSIS
nos-tun -t tunnel -s source -d destination -p protocol_number [source] target
DESCRIPTION
The nos-tun utility is used to establish an nos style tunnel, (also known as ka9q or IP-IP tunnel) using a tun(4) kernel interface.
Tunnel is the name of the tunnel device /dev/tun0 for example.
Source and destination are the addresses used on the tunnel device. If you configure the tunnel against a cisco router, use a netmask of
``255.255.255.252'' on the cisco. This is because the tunnel is a point-to-point interface in the FreeBSD end, a concept cisco does not
really implement.
Protocol number sets tunnel mode. Original KA9Q NOS uses 94 but many people use 4 on the worldwide backbone of ampr.org.
Target is the address of the remote tunnel device, this must match the source address set on the remote end.
EXAMPLES
This end, a FreeBSD box on address 192.168.59.34:
nos-tun -t /dev/tun0 -s 192.168.61.1 -d 192.168.61.2 192.168.56.45
Remote cisco on address 192.168.56.45:
interface tunnel 0
ip address 192.168.61.2 255.255.255.252
tunnel mode nos
tunnel destination 192.168.59.34
tunnel source 192.168.56.45
AUTHORS
Nickolay N. Dudorov <nnd@itfs.nsk.su> wrote the program, Poul-Henning Kamp <phk@FreeBSD.org> wrote the man-page. Isao SEKI
<iseki@gongon.com> added a new flag, IP protocol number.
BUGS
We do not allow for setting our source address for multihomed machines.
BSD April 11, 1998 BSD