I need to delete a TTY in my AIX 4.3 system. I have tried using the smit but everytime I try it, there is a message telling me that the device is in use and cannot be changed. How do I take the device "offline", so to speak, so that I can edit the settings and/or delete it.
V/R
Djassi (3 Replies)
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Hi, I have the following packages installed on my AIX server
xlC.aix50.rte 10.1.0.2 COMMITTED XL C/C++ Runtime for AIX 5.3
xlC.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.rte 10.1.0.2 COMMITTED XL C/C++ Runtime
xlC.rte... (4 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR.
How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a... (1 Reply)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only.
... (1 Reply)
Discussion started by: alphatron150
1 Replies
LEARN ABOUT OSF1
netconfig
netconfig(8) System Manager's Manual netconfig(8)NAME
netconfig - Launches the SysMan Menu to the Network Setup Wizard
SYNOPSIS
/usr/sbin/netconfig
/usr/sbin/sysman net_wizard
DESCRIPTION
The Network Setup Wizard of the SysMan Menu can be used to configure and modify the configuration of a TCP/IP network on a Tru64 UNIX sys-
tem.
Use the Network Setup Wizard, netconfig, to do the following: Configure network interfaces, such as Ethernet, FDDI and Token Ring and
existing ATM interfaces Enable and disable the following daemons: gated, joind, routed, and rwhod Configure the system as an IP router Add,
modify, and delete entries in the following files: /etc/routes, /etc/gateways, etc/hosts, /etc/hosts.equiv, and /etc/networks
Online help is available for the Network Management dialog boxes. To get help, click on any Help button.
RESTRICTIONS
You must be root or have the appropriate privileges to run this application.
FILES
Specifies the environment variables that define the netconfig configuration on your system Specifies Internet routing information Specifies
the host name file Specifies the trusted hosts file Specifies the network name file Specifies Internet static routing information
SEE ALSO
Commands: ifconfig(8), netsetup(8), rc.config(8), rcinet(8), sysman_menu(8)
Files: gateways(4), hosts(4), hosts.equiv(4), networks(4), routes(4)
Networking: network_manual_setup(7)netconfig(8)