I need to delete a TTY in my AIX 4.3 system. I have tried using the smit but everytime I try it, there is a message telling me that the device is in use and cannot be changed. How do I take the device "offline", so to speak, so that I can edit the settings and/or delete it.
V/R
Djassi (3 Replies)
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Hi, I have the following packages installed on my AIX server
xlC.aix50.rte 10.1.0.2 COMMITTED XL C/C++ Runtime for AIX 5.3
xlC.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.rte 10.1.0.2 COMMITTED XL C/C++ Runtime
xlC.rte... (4 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR.
How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a... (1 Reply)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only.
... (1 Reply)
Discussion started by: alphatron150
1 Replies
LEARN ABOUT OPENSOLARIS
xge
xge(7D) Devices xge(7D)NAME
xge - Neterion Xframe 10Gigabit Ethernet Network Adapter driver
SYNOPSIS
/dev/xge
DESCRIPTION
The xge 10 Gigabit Ethernet driver is a multi-threaded, loadable, clonable, GLD-based STREAMS driver supporting the Data Link Provider
Interface, dlpi(7P), on S2IO Xframe 10-Gigabit Ethernet Network Adapter.
The xge driver functions includes controller initialization, frame transmit and receive, promiscuous and multicast support, TCP and UDP
checksum offload (IPv4 and IPv6), 9622-byte jumbo frame, and error recovery and reporting.
The xge driver and hardware support the 10GBase-SR/W, LR/W, and ER/W 802.3 physical layer.
APPLICATION PROGRAMMING INTERFACE
The cloning, character-special device /dev/xge is used to access all Xframe devices installed within the system.
The xge driver is managed by the dladm(1M) command line utility, which allows VLANs to be defined on top of xge instances and for xge
instances to be aggregated. See dladm(1M) for more details.
The values returned by the driver in the DL_INFO_ACK primitive in response to the DL_INFO_REQ are as follows:
o Maximum SDU is 9600.
o Minimum SDU is 0.
o DSLAP address length is 8 bytes.
o MAC type is DL_ETHER.
o SAP length value is -2 meaning the physical address component is followed immediately by a 2-byte sap component within the
DLSAP address.
o Broadcast address value is Ethernet/IEEE broadcast address (FF:FF:FF:FF:FF:FF).
CONFIGURATION
By default, the xge driver works without any configuration file.
You can check the running-time status of a device instance using ndd(1M). Currently, the driver provides an interface to print all hard-
ware statistics.
For example, to print statistics of device xge0:
#ndd /dev/xge0 stats
tmac_data_octets 772
tmac_frms 15
tmac_drop_frms 0
tmac_bcst_frms 6
tmac_mcst_frms 6
...
rmac_vld_frms 13
rmac_fcs_err_frms 0
rmac_drop_frms 0
rmac_vld_bcst_frms 7
rmac_vld_mcst_frms 11
rmac_out_rng_len_err_frms 0
rmac_in_rng_len_err_frms 0
rmac_long_frms 0
...
not_traffic_intr_cnt 242673
traffic_intr_cnt 28
...
FILES
/dev/xge xge special character device
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------------------------------------+
|ATTRIBUTE TYPE ATTRIBUTE VALUE |
|Architecture x86 |
+-----------------------------------------------------------+
SEE ALSO dladm(1M), ndd(1M), attributes(5), streamio(7I), dlpi(7P)
Writing Device Drivers
STREAMS Programming Guide
Network Interfaces Programmer's Guide
SunOS 5.11 3 Oct 2005 xge(7D)