I need to delete a TTY in my AIX 4.3 system. I have tried using the smit but everytime I try it, there is a message telling me that the device is in use and cannot be changed. How do I take the device "offline", so to speak, so that I can edit the settings and/or delete it.
V/R
Djassi (3 Replies)
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Hi, I have the following packages installed on my AIX server
xlC.aix50.rte 10.1.0.2 COMMITTED XL C/C++ Runtime for AIX 5.3
xlC.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.rte 10.1.0.2 COMMITTED XL C/C++ Runtime
xlC.rte... (4 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR.
How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a... (1 Reply)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only.
... (1 Reply)
Discussion started by: alphatron150
1 Replies
LEARN ABOUT NETBSD
bridge
BRIDGE(4) BSD Kernel Interfaces Manual BRIDGE(4)NAME
bridge -- network bridge device
SYNOPSIS
pseudo-device bridge
DESCRIPTION
The bridge driver creates a logical link between two or more IEEE 802 networks that use the same (or ``similar enough'') framing format. For
example, it is possible to bridge Ethernet and 802.11 networks together, but it is not possible to bridge Ethernet and Token Ring together.
To use bridge, the administrator must first create the interface and configure the bridge parameters. The bridge is created using the
ifconfig(8) create subcommand. The learning and forwarding behavior and other parameters of a bridge are configured by the brconfig(8) util-
ity.
A bridge can be used to provide several services, such as a simple 802.11-to-Ethernet bridge for wireless hosts, and traffic isolation.
A bridge works like a switch, forwarding traffic from one interface to another. Multicast and broadcast packets are always forwarded to all
interfaces that are part of the bridge. For unicast traffic, the bridge learns which MAC addresses are associated with which interfaces and
will forward the traffic selectively.
The bridge driver implements the IEEE 802.1D Spanning Tree protocol (STP). Spanning Tree is used to detect and remove loops in a network
topology.
Transparent filtering for IP and IPv6 packets can be added with the kernel configuration option options BRIDGE_IPF.
When filtering is enabled, bridged packets will pass through the filter inbound on the originating interface and outbound on the appropriate
interfaces. ARP and REVARP packets are forwarded without being filtered and others that are not IP nor IPv6 packets are not forwarded when
filtering is enabled.
Note that packets to and from the bridging host will be seen by the filter on the interface with the appropriate address configured as well
as on the interface on which the packet arrives or departs.
SEE ALSO etherip(4), options(4), brconfig(8), ipf(8)HISTORY
The bridge driver first appeared in NetBSD 1.6.
AUTHORS
The bridge driver was originally written by Jason L. Wright <jason@thought.net> as part of an undergraduate independent study at the Univer-
sity of North Carolina at Greensboro.
This version of the bridge driver has been heavily modified from the original version by Jason R. Thorpe <thorpej@wasabisystems.com>.
BUGS
The bridge driver currently supports only Ethernet and Ethernet-like (e.g. 802.11) network devices, with exactly the same interface MTU size
as the bridge device.
The bridge driver currently does not support snooping via bpf(4).
BSD January 9, 2010 BSD