|
|
Sponsored Content
Operating Systems
AIX
AIX - NIC device explanation need
Post 303035317 by Phat on Tuesday 21st of May 2019 05:43:09 AM
05-21-2019
|
|
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I need to delete a TTY in my AIX 4.3 system. I have tried using the smit but everytime I try it, there is a message telling me that the device is in use and cannot be changed. How do I take the device "offline", so to speak, so that I can edit the settings and/or delete it.
V/R
Djassi (3 Replies)
Discussion started by: djassi
3 Replies
2. UNIX for Dummies Questions & Answers
I am a beginer in unix .
I would like to know what is the command in orser to change NIC and Device NO (1 Reply)
Discussion started by: Ilias Kappatos
1 Replies
3. AIX
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies
4. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
5. AIX
Hi, I have the following packages installed on my AIX server
xlC.aix50.rte 10.1.0.2 COMMITTED XL C/C++ Runtime for AIX 5.3
xlC.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.rte 10.1.0.2 COMMITTED XL C/C++ Runtime
xlC.rte... (4 Replies)
Discussion started by: jimthompson
4 Replies
6. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
7. AIX
NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR.
How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a... (1 Reply)
Discussion started by: gps1976
1 Replies
8. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
9. UNIX for Beginners Questions & Answers
I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only.
... (1 Reply)
Discussion started by: alphatron150
1 Replies
LEARN ABOUT OPENSOLARIS
sfe
sfe(7D) Devices sfe(7D) NAME
sfe - SiS900 series Fast Ethernet device driver SYNOPSIS
/dev/sfe DESCRIPTION
The sfe driver is a loadable, clonable, GLD-based STREAMS driver supporting the Data Link Provider Interface dlpi(7P) on Silicon Inte- grated Systems 900 series Fast Ethernet controllers. APPLICATION PROGRAMMING INTERFACE
The relevant fields returned as part of a DL_INFO_ACK response are: o Maximum SDU is 1500. o Minimum SDU is 0. o The dlsap address length is 8. o MAC type is DL_ETHER. o SAP length is -2. The 6-byte physical address is followed immediately by a 2-byte SAP. o Service mode is DL_CLDLS. o Broadcast address is the 6-byte Ethernet broadcast address (ff:ff:ff:ff:ff:ff). If the SAP provided is zero, then IEEE 802.3 mode is assumed and outbound frames will have the frame payload length written into the type field. Likewise, inbound frames with a SAP between zero and 1500 are interpreted as IEEE 802.3 frames and delivered to any streams that are bound to SAP zero (the 802.3 SAP). PROPERTIES
The following properties may be configured using either ndd(1M) or the sfe.conf configuration file as described by driver.conf(4): adv_100fdx_cap Enables the 100 Base TX full-duplex link option. (This is generally the fastest mode if both link partners support it. Most modern equipment supports this mode.) adv_100hdx_cap Enables the 100 Base TX half-duplex link option. (Typically used when the link partner is a 100 Mbps hub.) adv_10fdx_cap Enables the 10 Base-T full-duplex link option. (This less-frequently used mode is typically used when the link partner is a 10 Mbps switch.) adv_10hdx_cap Enables the 10 Base-T half-duplex link option. (This is the fall-back when no other option is available. It is typically used when the link partner is a 10 Mbps hub or is an older network card.) ATTRIBUTES
See attributes(5) for a description of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SPARC, x86 | +-----------------------------+-----------------------------+ |Interface Stability |Committed | +-----------------------------+-----------------------------+ FILES
/dev/sfe Special character device. /kernel/drv/sfe 32-bit driver binary (x86). /kernel/drv/amd64/sfe 64-bit driver binary (x86). /kernel/drv/sparcv9/sfe 64-bit driver binary (SPARC). /kernel/drv/sfe.conf Configuration file. SEE ALSO
ndd(1M), driver.conf(4), attributes(5), streamio(7I), dlpi(7P) IEEE 802.3 -- Institute of Electrical and Electronics Engineers, 2002 SunOS 5.11 12 Dec 2007 sfe(7D)