smitty tcpip --> Further configuration -->Network interface -->Network interface selection -->Configure alias
I have gone through this, but I don't see the alias IP. I think we have to put the alias IP here to remove. It's not already there for us to choose to remove
Code:
Type or select values in entry fields.
Press Enter AFTER making all desired changes.
[Entry Fields]
Network INTERFACE en6
* IPV4 ADDRESS (dotted decimal) []
Network MASK (hexadecimal or dotted decimal) []
1 more question, in the linux we can edit the ifcfg-ethx to make some changes. So on AIX, which file can we do the same to make changes to IP configuration?
I need to delete a TTY in my AIX 4.3 system. I have tried using the smit but everytime I try it, there is a message telling me that the device is in use and cannot be changed. How do I take the device "offline", so to speak, so that I can edit the settings and/or delete it.
V/R
Djassi (3 Replies)
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Hi, I have the following packages installed on my AIX server
xlC.aix50.rte 10.1.0.2 COMMITTED XL C/C++ Runtime for AIX 5.3
xlC.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.rte 10.1.0.2 COMMITTED XL C/C++ Runtime
xlC.rte... (4 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR.
How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a... (1 Reply)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only.
... (1 Reply)
Discussion started by: alphatron150
1 Replies
LEARN ABOUT OSX
finger.conf
FINGER.CONF(5) BSD File Formats Manual FINGER.CONF(5)NAME
finger.conf --finger(1) alias configuration file
DESCRIPTION
The optional finger.conf file is used to provide aliases that can be fingered by local and network users. This may be useful where a user's
login name is not the same as their preferred mail address, or for providing virtual login names than can be fingered.
Lines beginning with ``#'' are comments. Other lines must consist of an alias name and a target name separated by a colon. A target name
should be either a user, a forward reference to another alias or the path of a world readable file.
Where an alias points to a file, the contents of that file will be displayed when the alias is fingered.
FILES
/etc/finger.conf finger(1) alias definition data base
EXAMPLES
# /etc/finger.conf alias definition file
#
# Format alias:(user|alias)
#
# Individual aliases
#
markk:mkn
john.smith:dev329
john:dev329
sue:/etc/finger/sue.txt
#
# Network status message
#
status:/usr/local/etc/status.txt
#
# Administrative redirects
#
root:admin
postmaster:admin
abuse:admin
#
# For the time being, 'sod' is sysadmin.
#
admin:sod
SEE ALSO finger(1)HISTORY
Support for the finger.conf file was submitted by Mark Knight <markk@knigma.org> and first appeared in FreeBSD 4.2.
BSD August 16, 2000 BSD
05-17-2019
