05-14-2019
10 More Discussions You Might Find Interesting
1. AIX
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
2. IP Networking
WE are running Unix - Solaris 2.6, we create a subnet. In the windows enviroment we are able to add a static route by using
route add -p 172.16.10.0 mask 255.255.255.0 172.16.17.224, but when we add the route in Solaris as
route add -net 172.16.10.0 255.255.255.0 172.16.17.224, we receive an... (5 Replies)
Discussion started by: cassy
5 Replies
3. IP Networking
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies
4. HP-UX
Hi,
My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13
I tried with:
#route add 192.168.80.2 255.255.255.255 10.10.10.13
but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable
I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies
5. IP Networking
I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system.
The ip i am trying to get to is 172.16.4.48
I need to get to it via the hme1 interface.
The vpn gateway has this ip 172.30.50.1
I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies
6. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
7. IP Networking
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies
8. Solaris
Hey Guys:
I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1
add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies
9. Solaris
Hi need to add 2 routes, one on each server.
I know the route add comand but I have always been given the parameters to put in.
I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ?
In... (6 Replies)
Discussion started by: vettec3
6 Replies
10. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
RIPD(8) Version 0.97.3 RIPD(8)
NAME
ripd - a RIP routing engine for use with Quagga routing software.
SYNOPSIS
ripd [ -dhrv ] [ -f config-file ] [ -i pid-file ] [ -P port-number ] [ -A vty-address ] [ -u user ] [ -g group ]
DESCRIPTION
ripd is a routing component that works with the Quagga routing engine.
OPTIONS
Options available for the ripd command:
OPTIONS
-d, --daemon
Runs in daemon mode, forking and exiting from tty.
-f, --config-file config-file
Specifies the config file to use for startup. If not specified this option will likely default to /usr/local/etc/ripd.conf.
-g, --group group
Specify the group to run as. Default is quagga.
-h, --help
A brief message.
-i, --pid_file pid-file
When ripd starts its process identifier is written to pid-file. The init system uses the recorded PID to stop or restart ripd. The
likely default is /var/run/ripd.pid.
-P, --vty_port port-number
Specify the port that the ripd VTY will listen on. This defaults to 2602, as specified in /etc/services.
-A, --vty_addr vty-address
Specify the address that the ripd VTY will listen on. Default is all interfaces.
-u, --user user
Specify the user to run as. Default is quagga.
-r, --retain
When the program terminates, retain routes added by ripd.
-v, --version
Print the version and exit.
FILES
/usr/local/sbin/ripd
The default location of the ripd binary.
/usr/local/etc/ripd.conf
The default location of the ripd config file.
$(PWD)/ripd.log
If the ripd process is config'd to output logs to a file, then you will find this file in the directory where you started ripd.
WARNING
This man page is intended to be a quick reference for command line options. The definitive document is the Info file Quagga.
DIAGNOSTICS
The ripd process may log to standard output, to a VTY, to a log file, or through syslog to the system logs. ripd supports many debugging
options, see the Info file, or the source for details.
SEE ALSO
bgpd(8), ripngd(8), ospfd(8), ospf6d(8), isisd(8), zebra(8), vtysh(1)
BUGS
ripd eats bugs for breakfast. If you have food for the maintainers try http://bugzilla.quagga.net
AUTHORS
See http://www.zebra.org and http://www.quagga.net or the Info file for an accurate list of authors.
Quagga RIP daemon 25 November 2004 RIPD(8)