Sponsored Content
Full Discussion: Add explicit route
Special Forums IP Networking Add explicit route Post 303035078 by Neo on Tuesday 14th of May 2019 01:18:53 AM
Old 05-14-2019
Normally, when a system builds a routing table based on routes up or routes down, they use a dynamic routing protocol.

Static routes are static. Dynamic routes are dynamic.

For example, rip:

ripd - a RIP routing engine for use with Quagga routing software.

or ospf

See, for example:

OSPF (Open Shortest Path First) - Linux | Network Command Reference

So, if I were you, and I needed dynamic routes, I would quickly set up dynamic routing. Static routes are the wrong tool for dynamic routes, as I understand your question.
 

10 More Discussions You Might Find Interesting

1. AIX

route add

Hello , We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ... #route add server.ip router.ip after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies

2. IP Networking

add route to a subnet - Solaris 2.6

WE are running Unix - Solaris 2.6, we create a subnet. In the windows enviroment we are able to add a static route by using route add -p 172.16.10.0 mask 255.255.255.0 172.16.17.224, but when we add the route in Solaris as route add -net 172.16.10.0 255.255.255.0 172.16.17.224, we receive an... (5 Replies)
Discussion started by: cassy
5 Replies

3. IP Networking

Do I need to add a route??

I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0. My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network. My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies

4. HP-UX

Add Route on HP-UX v10.x, help.

Hi, My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13 I tried with: #route add 192.168.80.2 255.255.255.255 10.10.10.13 but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies

5. IP Networking

Route add probleme

I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system. The ip i am trying to get to is 172.16.4.48 I need to get to it via the hme1 interface. The vpn gateway has this ip 172.30.50.1 I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies

6. Solaris

Route Add

Hi, I am trying to add route command in Solaris 10 machine in the following fashion: route add -host 10.8.112.10 180.144.1.250 -interface lo0:1 this command fails with an error "lo0:1: bad value" I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies

7. IP Networking

route add

I have built a new linux server, via a iLo connection. and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty. Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies

8. Solaris

route add : network is unreachable

Hey Guys: I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1 add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies

9. Solaris

Add route to solaris10

Hi need to add 2 routes, one on each server. I know the route add comand but I have always been given the parameters to put in. I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ? In... (6 Replies)
Discussion started by: vettec3
6 Replies

10. Solaris

Add route to solaris 10

I need to add a new route on solaris10 machine. I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway. How I do ? Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
VDE_L3(1)						      General Commands Manual							 VDE_L3(1)

NAME
vde_l3 - Virtual Distributed Ethernet 'Layer 3' Switch. SYNOPSIS
vde_l3 -v vde_plug:ipaddress/netmask [-v...] [-r target_network/netmask:gateway] [-G default_gw] [-M mgmt_socket] DESCRIPTION
A vde_l3 connects to one or more vde_switches, performing ip forwarding among its virtual interfaces. A new interface is created at startup for each -v option given at command line. Static routes to target networks can be defined using the -r option. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 connects to the vde sock at /var/run/s1.ctl with its virtual interface ve0, having the address 192.168.0.1 and netmask 255.255.255.0. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 -v /var/run/s2.ctl:10.0.0.254/255.255.0.0 connects to the two vde socks, with its virtual interfaces ve0 and ve1, having addressess 192.168.1.0 and 10.0.0.254 respectively. Hosts in each network can specify the vde_l3 as their gateway to reach the other one. OPTIONS
-v vde_plug:ipaddress/netmask Creates a virtual network interfaces on the vde_l3 box, with address ipaddress and netmask netmask. Please note that the netmask can be specified either in the 'classic' A.B.C.D mode, or just by giving the number of leading bits (f.e., /17 for 255.255.128.0). One can define as many interfaces as she wants. -r target_network/netmask:gateway Specify a static route through gateway to reach hosts in target_network with netmask netmask. One can define as many routes as she wants. -G default_gw Specify a default gateway, to be used whenever no static route is defined for a target host. -M mgmt_socket the unix socket where the parameters (interfaces addresses, routes, etc.) can be checked and changed runtime. unixterm(1) can be used as a remote terminal for wirefilter. NOTICE
Virtual Distributed Ethernet is not related in any way with www.vde.com ("Verband der Elektrotechnik, Elektronik und Informationstechnik" i.e. the German "Association for Electrical, Electronic & Information Technologies"). SEE ALSO
vde_switch(1), vdeq(1), unixterm(1), vde_cryptcab(1), wirefilter(1). AUTHORS
VDE_L3 is a tool by Daniele Lacamera <root@danielinux.net> VDE is a project by Renzo Davoli <renzo@cs.unibo.it> Virtual Distributed Ethernet May 7, 2007 VDE_L3(1)
All times are GMT -4. The time now is 12:14 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy