Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Fibre Channel link not ready on Netra 240
Operating Systems Solaris Fibre Channel link not ready on Netra 240 Post 303034471 by hicksd8 on Friday 26th of April 2019 01:49:46 PM
Old 04-26-2019
Well it would be a bit of a tragedy if you replace the motherboard but this one is fixable. The diags recognises that there's a QLogic chipset on the PCI bus but announces a failure. Take a look at the enablecomponent command in case the device has been accidentally blacklisted. Also, the QLogic BIOS announcement at boot time may be/could be disabled so try (several times) to enter CTRL-Q as the box boots to see if you can enter the QLogic BIOS setup. That would at least prove that it's talking.

You have a QLogic chipset that is being recognised but not passing diags.

Since you say this is an on-board adapter then it could mean a motherboard change but that's a bit drastic if it's caused by just some setting.
 

10 More Discussions You Might Find Interesting

1. Solaris

Netra 240 Hard disk are not detected

Hi All, I have new Netra 240 box which is not detecting its harddisk equiped with itse same har disk are detected when I swap with another machine. Same time If I swap hardisk of other machine to this Netra 240 box, also do not work. I have checked chassis, cabling etc and all looks fine. ... (1 Reply)
Discussion started by: xpwistler
1 Replies

2. AIX

Fibre channel drivers on RS/6000 aix 5L

Want to configure IBM raid strorage but the aix 5L cds do not have the drivers for the fibre channels. The machine is RS/6000. I have gone to IBM downlaodable sites but i can't find the drivers? help pliz:mad: (4 Replies)
Discussion started by: Zim-Aix-Guru
4 Replies

3. AIX

Power6 Virtual Fibre Channel Adapter

Hello, Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter. It is similar to virtual scsi adapter. In my client partition I created the virtual Fibre Adapter mapped it with the VIO... (1 Reply)
Discussion started by: filosophizer
1 Replies

4. Solaris

netra 240 difference

Hi, sunfire v240 and netra 240 are looks similar. system board, memory and processors are similar, then why netra 240 called as telco server? can anyone tell the difference. RJS (1 Reply)
Discussion started by: rajasekg
1 Replies

5. Solaris

USCSICMD ioctl calls for Fibre Channel(FC) devices on Solaris 10?

Hi , I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Discussion started by: naveen448
0 Replies

6. Solaris

SUN Netra 240 Boot error

Hi, When I am trying to boot my SUN Netra 240 Machine its giving some boot error. > {1} ok boot -i > Boot device: /pci@1c,600000/scsi@2/disk@0,0:a File and args: -i > Boot load failed. > The file just loaded does not appear to be executable. > {1} ok I tried to boot it from cdrom... (9 Replies)
Discussion started by: ppandey21
9 Replies

7. Hardware

Fibre Channel HBA recommendations?

We will be buying new Xeon E5-based servers for our datacenter and were wondering which Fibre Channel host bus adapters we should select for these. The choices are Emulex or QLogic (8Gb FC HBAs). Anybody have any recommendations on which is the better choice? Thanks in advance. (1 Reply)
Discussion started by: atahmass
1 Replies

8. Hardware

POST displays error sparc netra 240

Hi guys, when I power on my sun netra 240 server, it displays these error messages: 1. Notice: cpu 0 has 2048/2048 MB of memory disabled. 2. Error : The following devices are disabled dimm1. Please can anyone be kind enough to explain this for me? Thanks (2 Replies)
Discussion started by: cjashu
2 Replies

9. Solaris

Fibre channel link down on booting Solaris server

Hi I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10. After power on the system stops at ok prompt, them I issued the following commands: {0} ok setenv auto-boot? false auto-boot? = false {0} ok reset-all SPARC T3-1B,... (10 Replies)
Discussion started by: fretagi
10 Replies

10. AIX

[ASK] - AIX Fibre Channel behavior

Hello all, Let me introduce about the context and my environment. We have an AIX 6.1 system, it has 4 FC channels / > lsdev -Cc adapter | grep fcs fcs0 Available 23-T1 Virtual Fibre Channel Client Adapter fcs1 Available 23-T1 Virtual Fibre Channel Client Adapter fcs2 Available 23-T1... (14 Replies)
Discussion started by: Phat
14 Replies

LEARN ABOUT FREEBSD

if_qlxgb

QLXGB(4)						   BSD Kernel Interfaces Manual 						  QLXGB(4)

NAME

     qlxgb -- QLogic 10 Gigabit Ethernet & CNA Adapter Driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device qlxgb

     To load the driver as a module at boot time, place the following line in loader.conf(5):

	   if_qlxgb_load="YES"

DESCRIPTION

     The qlxgb driver supports IPv4 checksum offload, TCP and UDP checksum offload for both IPv4 and IPv6, Large Segment Offload for both IPv4 and
     IPv6, Jumbo frames, VLAN Tag, and Receive Side scaling.  For further hardware information, see http://www.qlogic.com/.

HARDWARE

     The qlxgb driver supports 10 Gigabit Ethernet & CNA Adapter based on the following chipsets:

     o	 QLogic 3200 series
     o	 QLogic 8200 series

SUPPORT

     For support questions please contact your QLogic approved reseller or QLogic Technical Support at http://support.qlogic.com, or by E-mail at
     <support@qlogic.com>.

SEE ALSO

     altq(4), arp(4), netintro(4), ng_ether(4), ifconfig(8)

HISTORY

     The qlxgb device driver first appeared in FreeBSD 10.0.

AUTHORS

     The qlxgb driver was written by David C Somayajulu at QLogic Corporation.

BSD
								 November 3, 2011							       BSD
All times are GMT -4. The time now is 04:29 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy