04-26-2019
Well it would be a bit of a tragedy if you replace the motherboard but this one is fixable. The diags recognises that there's a QLogic chipset on the PCI bus but announces a failure. Take a look at the enablecomponent command in case the device has been accidentally blacklisted. Also, the QLogic BIOS announcement at boot time may be/could be disabled so try (several times) to enter CTRL-Q as the box boots to see if you can enter the QLogic BIOS setup. That would at least prove that it's talking.
You have a QLogic chipset that is being recognised but not passing diags.
Since you say this is an on-board adapter then it could mean a motherboard change but that's a bit drastic if it's caused by just some setting.
10 More Discussions You Might Find Interesting
1. Solaris
Hi All,
I have new Netra 240 box which is not detecting its harddisk equiped with itse same har disk are detected when I swap with another machine.
Same time If I swap hardisk of other machine to this Netra 240 box, also do not work. I have checked chassis, cabling etc and all looks fine. ... (1 Reply)
Discussion started by: xpwistler
1 Replies
2. AIX
Want to configure IBM raid strorage but the aix 5L cds do not have the drivers for the fibre channels. The machine is RS/6000. I have gone to IBM downlaodable sites but i can't find the drivers? help pliz:mad: (4 Replies)
Discussion started by: Zim-Aix-Guru
4 Replies
3. AIX
Hello,
Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter.
It is similar to virtual scsi adapter.
In my client partition I created the virtual Fibre Adapter mapped it with the VIO... (1 Reply)
Discussion started by: filosophizer
1 Replies
4. Solaris
Hi,
sunfire v240 and netra 240 are looks similar. system board, memory and processors are similar, then why netra 240 called as telco server?
can anyone tell the difference.
RJS (1 Reply)
Discussion started by: rajasekg
1 Replies
5. Solaris
Hi ,
I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Discussion started by: naveen448
0 Replies
6. Solaris
Hi,
When I am trying to boot my SUN Netra 240 Machine its giving some boot error.
> {1} ok boot -i
> Boot device: /pci@1c,600000/scsi@2/disk@0,0:a File and args: -i
> Boot load failed.
> The file just loaded does not appear to be executable.
> {1} ok
I tried to boot it from cdrom... (9 Replies)
Discussion started by: ppandey21
9 Replies
7. Hardware
We will be buying new Xeon E5-based servers for our datacenter and were wondering which Fibre Channel host bus adapters we should select for these. The choices are Emulex or QLogic (8Gb FC HBAs). Anybody have any recommendations on which is the better choice?
Thanks in advance. (1 Reply)
Discussion started by: atahmass
1 Replies
8. Hardware
Hi guys,
when I power on my sun netra 240 server,
it displays these error messages:
1. Notice: cpu 0 has 2048/2048 MB of memory disabled.
2. Error : The following devices are disabled dimm1.
Please can anyone be kind enough to explain this for me?
Thanks (2 Replies)
Discussion started by: cjashu
2 Replies
9. Solaris
Hi
I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10.
After power on the system stops at ok prompt, them I issued the following commands:
{0} ok setenv auto-boot? false
auto-boot? = false
{0} ok reset-all
SPARC T3-1B,... (10 Replies)
Discussion started by: fretagi
10 Replies
10. AIX
Hello all,
Let me introduce about the context and my environment.
We have an AIX 6.1 system, it has 4 FC channels
/ > lsdev -Cc adapter | grep fcs
fcs0 Available 23-T1 Virtual Fibre Channel Client Adapter
fcs1 Available 23-T1 Virtual Fibre Channel Client Adapter
fcs2 Available 23-T1... (14 Replies)
Discussion started by: Phat
14 Replies
LEARN ABOUT NETBSD
pnpbios
PNPBIOS(4) BSD/i386 Kernel Interfaces Manual PNPBIOS(4)
NAME
pnpbios -- support for embedded devices on the motherboard
DESCRIPTION
The pnpbios driver enumerates embedded ISA devices on the motherboard whose BIOS supports ``Plug and Play BIOS Specification''. It assigns
ISA bus resources (interrupt line, DMA channel, I/O ports, and memory region) to each device and activates it.
If it cannot assign necessary resources to a device without causing conflict with other devices in the system, the device will not be acti-
vated and will be unavailable to programs.
CAVEATS
There is no explicit way to disable individual embedded devices. The pnpbios driver will find all devices reported by the ``Plug and Play
(PnP)'' BIOS and try to activate them all.
There is no way to explicitly assign particular resource to a device. The resource assignment is fully automatic and there is no provision
for manual override.
SEE ALSO
pnp(4)
STANDARDS
Compaq, Phenix, and Intel, Plug and Play BIOS Specification Version 1.0A, May 5, 1994.
Compaq, Phenix, and Intel, Plug and Play BIOS CLARIFICATION Paper for Plug and Play BIOS Specification Version 1.0A, October 6, 1994.
HISTORY
The pnpbios driver first appeared in FreeBSD 4.0.
AUTHORS
The pnpbios driver was written by Mike Smith.
BSD September 20, 2001 BSD