|
|
Sponsored Content
Operating Systems
Solaris
Fibre Channel link not ready on Netra 240
Post 303034449 by hicksd8 on Friday 26th of April 2019 06:19:01 AM
|
|
10 More Discussions You Might Find Interesting
1. Solaris
Hi All,
I have new Netra 240 box which is not detecting its harddisk equiped with itse same har disk are detected when I swap with another machine.
Same time If I swap hardisk of other machine to this Netra 240 box, also do not work. I have checked chassis, cabling etc and all looks fine. ... (1 Reply)
Discussion started by: xpwistler
1 Replies
2. AIX
Want to configure IBM raid strorage but the aix 5L cds do not have the drivers for the fibre channels. The machine is RS/6000. I have gone to IBM downlaodable sites but i can't find the drivers? help pliz:mad: (4 Replies)
Discussion started by: Zim-Aix-Guru
4 Replies
3. AIX
Hello,
Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter.
It is similar to virtual scsi adapter.
In my client partition I created the virtual Fibre Adapter mapped it with the VIO... (1 Reply)
Discussion started by: filosophizer
1 Replies
4. Solaris
Hi,
sunfire v240 and netra 240 are looks similar. system board, memory and processors are similar, then why netra 240 called as telco server?
can anyone tell the difference.
RJS (1 Reply)
Discussion started by: rajasekg
1 Replies
5. Solaris
Hi ,
I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Discussion started by: naveen448
0 Replies
6. Solaris
Hi,
When I am trying to boot my SUN Netra 240 Machine its giving some boot error.
> {1} ok boot -i
> Boot device: /pci@1c,600000/scsi@2/disk@0,0:a File and args: -i
> Boot load failed.
> The file just loaded does not appear to be executable.
> {1} ok
I tried to boot it from cdrom... (9 Replies)
Discussion started by: ppandey21
9 Replies
7. Hardware
We will be buying new Xeon E5-based servers for our datacenter and were wondering which Fibre Channel host bus adapters we should select for these. The choices are Emulex or QLogic (8Gb FC HBAs). Anybody have any recommendations on which is the better choice?
Thanks in advance. (1 Reply)
Discussion started by: atahmass
1 Replies
8. Hardware
Hi guys,
when I power on my sun netra 240 server,
it displays these error messages:
1. Notice: cpu 0 has 2048/2048 MB of memory disabled.
2. Error : The following devices are disabled dimm1.
Please can anyone be kind enough to explain this for me?
Thanks (2 Replies)
Discussion started by: cjashu
2 Replies
9. Solaris
Hi
I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10.
After power on the system stops at ok prompt, them I issued the following commands:
{0} ok setenv auto-boot? false
auto-boot? = false
{0} ok reset-all
SPARC T3-1B,... (10 Replies)
Discussion started by: fretagi
10 Replies
10. AIX
Hello all,
Let me introduce about the context and my environment.
We have an AIX 6.1 system, it has 4 FC channels
/ > lsdev -Cc adapter | grep fcs
fcs0 Available 23-T1 Virtual Fibre Channel Client Adapter
fcs1 Available 23-T1 Virtual Fibre Channel Client Adapter
fcs2 Available 23-T1... (14 Replies)
Discussion started by: Phat
14 Replies
LEARN ABOUT SUNOS
hpfc
hpfc(7D) Devices hpfc(7D) NAME
hpfc - Agilent fibre channel host bus adapter SYNOPSIS
PCI pci103c DESCRIPTION
The hpfc fibre channel host bus adapter is a SCSA compliant nexus driver that supports all Agilent fibre channel host bus adapters, includ- ing the HHBA5100x, HHBA5101x, and HHBA5121x models. Agilent host bus adapters support the fibre channel protocol on private fibre channel arbitrated loops and fabrics. The driver supports up to ten host bus adapters, with a maximum of 125 fibre channel devices on each host bus adapter. The hpfc driver supports a maximum of 256 LUNs per target. The hpfc driver does not support the BIOS Int 13 feature, which enables the booting of an operating system. As a result, you should not install an operating system on devices attached to the hpfc driver. CONFIGURATION
The hpfc driver attempts to configure itself using the information in the /kernel/drv/hpfc.conf configuration file. By default, the driver supports only LUN 0 for each target device. To add multiple LUN support, modify the /kernel/drv/sd.conf file. Before upgrading the hpfc driver, backup the sd.conf file to save customized LUN settings and then use pkgrm(1M) to remove the old version of the driver. The host bus adapter port is initialized to FL_Port when connected to a fabric switch. To change it to F_Port, add the init_as_nport=1 entry to the hpfc.conf file and reboot the system. To conserve system resources, at least one disk drive must be attached to the hpfc driver. If no devices are attached, the driver will not load. FILES
/kernel/drv/hpfc 32-bit ELF kernel module /kernel/drv/sparcv9/hpfc 64-bit ELF kernel module /kernel/drv/hpfc.conf Driver configuration file /kernel/drv/sd.conf SCSI disk configuration file ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Architecture |x86, SPARC | +-----------------------------+-----------------------------+ SEE ALSO
luxadm(1M), pkgrm(1M), prtconf(1M), driver.conf(4), attributes(5), ses(7D), ssd(7D) ANSI X3.272-1996, Fibre Channel Arbitrated Loop (FC-AL), ANSI X3.269-1996, Fibre Channel Protocol for SCSI (FCP), ANSI X3.270-1996, SCSI-3 Architecture Model (SAM), Fibre Channel Private Loop SCSI Direct Attach (FC-PLDA) SunOS 5.10 10 Oct 2000 hpfc(7D)