04-24-2019
There is no need to reboot Linux systems to change the IP address of set up network services.
8 More Discussions You Might Find Interesting
1. BSD
hi
howto restart the network with a wireless interface including wpa_supplicant on freeBSD 7.2 without reboot? (3 Replies)
Discussion started by: ccc
3 Replies
2. AIX
Hi All,
Please let me know the command to restart the network interface and enable it on boot in AIX, similar to /etc/init.d/network restart in Redhat.
Thanks,
Sunil.K
please watch out to post in the right subforum! (9 Replies)
Discussion started by: sunilrk07
9 Replies
3. UNIX for Advanced & Expert Users
I'm becoming a dying breed where I work. More and more sys admins are advocating automatically restarting failed services such as tomcat, jboss, etc. I've always been against doing this except with buggy apps that can't be fixed or avoided.
My main argument is that I feel it's a trick used by... (9 Replies)
Discussion started by: mglenney
9 Replies
4. AIX
hello,
i have an AIX6.1.7.2 machine that it was upgraded recently from AIX5.3.9.4.
when i kill system services that should restart automatically like /usr/sbin/cron it doesnt start.
i checked my /etc/inittab file and i confirmed that this service is in respawn status so when i kill this process... (2 Replies)
Discussion started by: omonoiatis9
2 Replies
5. Shell Programming and Scripting
Hi Guys,
I need bash script to restart the service.
1. Disable the service called SASM
svcadm disable sasm
2. if service went to maintenance mode then it shuld clear it with below command
svcadm clear sasm
3.or else it should restart the mysql service
/etc/init.d/mysql stop... (1 Reply)
Discussion started by: bapu1981
1 Replies
6. Shell Programming and Scripting
Hi,
could someone give me an example for a debian server script? I need to check a process if the process has a high cpu load (top).
If yes the whole server needs to reboot.
Thats it, nothing more. ;)
Hope someone could help me.
Regards
woisch (2 Replies)
Discussion started by: woisch
2 Replies
7. Red Hat
I had a doubt if any services need to be restarted if port no in /etc/services in an RHEL setup is changed. For eg, the port no of 443 for SSL may need to be changed.
I hope my query is clear whether any services need to be restarted if port no in /etc/services is changed.
Please revert with... (10 Replies)
Discussion started by: RHCE
10 Replies
8. Red Hat
Hi,
I have 2 machines in production environment:
1. redhat machine for application
2. DB machine (oracle)
The application doing a lot of small read&writes from and to the DB machine.
The problem is that after some few hours the network from the application to the DB becomes very slow and... (4 Replies)
Discussion started by: moshesa
4 Replies
LEARN ABOUT DEBIAN
setether
SETETHER(8) System Manager's Manual SETETHER(8)
NAME
setether - Set the ethernet address for use with DECnet
SYNOPSIS
setether <if> [<if>...]|all [options]
DESCRIPTION
Set ethernet MAC address on ethernet adaptors
This script should be run at system startup. It will change the ethernet hardware (MAC) address of any or all ethernet interfaces to match
the DECnet node address. DECnet requires that the MAC address of all ethernet adaptors running the protocol be set approriately. If you do
not run setether then you must change the ethernet address in some other way for DECnet to work.
By default no ethernet interfaces will have their MAC addresses changed by setether, if you specify all then all interfaces name eth* will
be changed, otherwise a list of interface names can be specified. setether will enable (UP) all interfaces it changes the MAC addresses
of.
(2.4 only) The first interface specified on the command-line will also be made the default interface for DECnet operations (ie attempts to
contact nodes not in the neighbour table will be done over this interface).
This script must be run with the interface inactive, it is normally run from /etc/init.d/decnet before TCP/IP starts up.
EXAMPLES
set the MAC address of eth0.
# /sbin/setether eth0
set the MAC address of all ethernet interfaces
# /sbin/setether all
HELPFUL HINTS
If you have multiple ethernet cards on your system and they are connected to the the same network you should specify which one you want to
use for DECnet communication on the setether command line, otherwise they will both be given the same MAC address and this is probably not
what you want.
Running DECnet on multiple ethernet interfaces only works under Linux 2.4. If you are running Linux 2.2 then the interface name on the
setether command line must match the one in /etc/decnet.conf(5).
SEE ALSO
decnet.conf(5), dntype(1), dndir(1), dndel(1), dnetd(8), dnping(1)
DECnet utilities March 01 2001 SETETHER(8)