04-17-2019
10 More Discussions You Might Find Interesting
1. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
2. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
3. IP Networking
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies
4. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
5. HP-UX
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies
6. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
7. HP-UX
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Discussion started by: mkiron
1 Replies
8. Solaris
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies
9. Solaris
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Discussion started by: primeaup
3 Replies
10. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
LEARN ABOUT CENTOS
enum_ieee80211_ampdu_mlme_action
ENUM
IEEE80211_AMPDU(9) Advanced driver interface ENUM IEEE80211_AMPDU(9)
NAME
enum_ieee80211_ampdu_mlme_action - A-MPDU actions
SYNOPSIS
enum ieee80211_ampdu_mlme_action {
IEEE80211_AMPDU_RX_START,
IEEE80211_AMPDU_RX_STOP,
IEEE80211_AMPDU_TX_START,
IEEE80211_AMPDU_TX_STOP_CONT,
IEEE80211_AMPDU_TX_STOP_FLUSH,
IEEE80211_AMPDU_TX_STOP_FLUSH_CONT,
IEEE80211_AMPDU_TX_OPERATIONAL
};
CONSTANTS
IEEE80211_AMPDU_RX_START
start RX aggregation
IEEE80211_AMPDU_RX_STOP
stop RX aggregation
IEEE80211_AMPDU_TX_START
start TX aggregation
IEEE80211_AMPDU_TX_STOP_CONT
stop TX aggregation but continue transmitting queued packets, now unaggregated. After all packets are transmitted the driver has to
call ieee80211_stop_tx_ba_cb_irqsafe.
IEEE80211_AMPDU_TX_STOP_FLUSH
stop TX aggregation and flush all packets, called when the station is removed. There's no need or reason to call
ieee80211_stop_tx_ba_cb_irqsafe in this case as mac80211 assumes the session is gone and removes the station.
IEEE80211_AMPDU_TX_STOP_FLUSH_CONT
called when TX aggregation is stopped but the driver hasn't called ieee80211_stop_tx_ba_cb_irqsafe yet and now the connection is
dropped and the station will be removed. Drivers should clean up and drop remaining packets when this is called.
IEEE80211_AMPDU_TX_OPERATIONAL
TX aggregation has become operational
DESCRIPTION
These flags are used with the ampdu_action callback in struct ieee80211_ops to indicate which action is needed.
Note that drivers MUST be able to deal with a TX aggregation session being stopped even before they OK'ed starting it by calling
ieee80211_start_tx_ba_cb_irqsafe, because the peer might receive the addBA frame and send a delBA right away!
AUTHOR
Johannes Berg <johannes@sipsolutions.net>
Author.
COPYRIGHT
Kernel Hackers Manual 3.10 June 2014 ENUM IEEE80211_AMPDU(9)