Thanks.
I was able to find a server, on which I can do "pull the cable test".
From below output, it shows that bnx1 cable was pulled out. since aggr is configured igb2 took the traffic and all link sustained. But first line shows "address: 3c:d9:2b:f9:20:5e (auto)" and this MAC address is for bnx1.
Since igb2 took all the traffic now and its mac is f4:ce:46:a7:df:ba , should it not show in auto ? Sorry, I am confused in understanding this.
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
LEARN ABOUT CENTOS
struct_sta_ampdu_mlme
STRUCT STA_AMPDU_MLM(9) Internals STRUCT STA_AMPDU_MLM(9)NAME
struct_sta_ampdu_mlme - STA aggregation information.
SYNOPSIS
struct sta_ampdu_mlme {
struct mutex mtx;
struct tid_ampdu_rx __rcu * tid_rx[IEEE80211_NUM_TIDS];
unsigned long tid_rx_timer_expired[BITS_TO_LONGS(IEEE80211_NUM_TIDS)];
unsigned long tid_rx_stop_requested[BITS_TO_LONGS(IEEE80211_NUM_TIDS)];
struct work_struct work;
struct tid_ampdu_tx __rcu * tid_tx[IEEE80211_NUM_TIDS];
struct tid_ampdu_tx * tid_start_tx[IEEE80211_NUM_TIDS];
unsigned long last_addba_req_time[IEEE80211_NUM_TIDS];
u8 addba_req_num[IEEE80211_NUM_TIDS];
u8 dialog_token_allocator;
};
MEMBERS
mtx
mutex to protect all TX data (except non-NULL assignments to tid_tx[idx], which are protected by the sta spinlock)
tid_rx[IEEE80211_NUM_TIDS]
aggregation info for Rx per TID -- RCU protected
tid_rx_timer_expired[BITS_TO_LONGS(IEEE80211_NUM_TIDS)]
bitmap indicating on which TIDs the RX timer expired until the work for it runs
tid_rx_stop_requested[BITS_TO_LONGS(IEEE80211_NUM_TIDS)]
bitmap indicating which BA sessions per TID the driver requested to close until the work for it runs
work
work struct for starting/stopping aggregation
tid_tx[IEEE80211_NUM_TIDS]
aggregation info for Tx per TID
tid_start_tx[IEEE80211_NUM_TIDS]
sessions where start was requested
last_addba_req_time[IEEE80211_NUM_TIDS]
timestamp of the last addBA request.
addba_req_num[IEEE80211_NUM_TIDS]
number of times addBA request has been sent.
dialog_token_allocator
dialog token enumerator for each new session;
AUTHOR
Johannes Berg <johannes@sipsolutions.net>
Author.
COPYRIGHT Kernel Hackers Manual 3.10 June 2014 STRUCT STA_AMPDU_MLM(9)