Hi,
I have Solaris-10 server and link aggregation is configured on this in below way
There will be switch replacement, so one by one, link will go down from one side. Before that activity, is there any way to check/test, if server will work fine, if one side goes down ? In same way, as used to check by if_mpadm -d in ipmp.
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
LEARN ABOUT OPENSOLARIS
amd8111s
amd8111s(7D) Devices amd8111s(7D)NAME
amd8111s - AMD-8111 Fast Ethernet Network Adapter driver
SYNOPSIS
/dev/amd8111s
DESCRIPTION
The amd8111s Fast Ethernet driver is a multi-threaded, loadable, clonable, GLD-based STREAMS driver supporting the Data Link Provider
Interface, dlpi(7P), on the AMD-8111 Fast Ethernet Network Adapter.
The amd8111s driver functions include controller initialization, frame transmit and receive, promiscuous and multicast support, and error
recovery and reporting.
APPLICATION PROGRAMMING INTERFACE
The cloning, character-special device /dev/amd8111 is used to access all AMD-8111 Fast Ethernet devices installed within the system.
The amd8111s driver is managed by the dladm(1M) command line utility, which allows VLANs to be defined on top of amd8111s instances and
for amd8111s instances to be aggregated. See dladm(1M) for more details.
CONFIGURATION
By default, the amd8111s driver performs auto-negotiation to select the link speed and mode. Link speed and mode can be any of the follow-
ing:
100 Mbps, full-duplex.
100 Mbps, half-duplex.
10 Mbps, full-duplex.
10 Mbps, half-duplex.
FILES
/dev/amd8111s*
Special character device.
/kernel/drv/amd8111s*
32-bit ELF kernel module (x86).
/kernel/drv/amd64/amd8111s*
64-bit ELF Kernel module (x86).
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------------------------------------+
|ATTRIBUTE TYPE ATTRIBUTE VALUE |
|Availability SUNW8111s |
|Architecture x86 |
|Interface Stability Committed |
+-----------------------------------------------------------+
SEE ALSO dladm(1M), attributes(5), streamio(7I), dlpi(7P)
Writing Device Drivers
STREAMS Programming Guide
Network Interfaces Programmer's Guide
SunOS 5.11 30 Jul 2007 amd8111s(7D)