Hi
I need to append some text @ end of the first line in a file.
like
myfile.txt
list = a,b,c
list.a=some..
I give the arg "d" . now it append at end of first line
list=a,b,c,d
list.a=some...
Please help me out this (7 Replies)
Say I have a text file like:
1
3
4
How would I use ksh to put the number '2' into the second line of that file? I'm using OpenBSD so the sed syntax might be a bit different (I have no idea how to use sed, though) (4 Replies)
Hello, this is probably a simple request but I've been toying with it for a while.
I have a large list of devices and commands that were run with a script, now I have lines such as:
a-router-hostname-C#show ver
I want to print everything up to (and excluding) the # and everything after it... (3 Replies)
I would like to add a line to the end of a single column text file. How do I go about doing that?
Input:
BEGIN
1
2
3
Output:
BEGIN
1
2
3
END
Thanks! (1 Reply)
I have a text file like this:
subject1:LecturerA:10
subject2:LecturerA:40
if I was given string in column 1 and 2 (which are subject 1 and LecturerA) , i need to update 3rd field of that line containing that given string , which is, number 10 need to be updated to 100 ,for example.
The... (6 Replies)
Hi,
I had generated a report in my tool as followsoutput.txt
43.35
9
i needed the script to generate a new file like below
i want to append the text to each of these lines of my filenewoutputfile.txt should be
Total Amount : 43.35
Record Count:9
Regards,
Vasa Saikumar.
... (2 Replies)
Hi,
Anyone can help on how to append a file1.txt into file2.txt after line 3 using sed command.
file1.txt
1. testa
2. testb
3. testc
4. testd
5. test5
6. test6
file2.txt
break here
this is a test
break end here
output
1. testa
2. testb (1 Reply)
I am trying to create a cronjob that will run on startup that will look at a list.txt file to see if there is a later version of a database using database.txt as the source. The matching lines are written to output.
$1 in database.txt will be in list.txt as a partial match. $2 of database.txt... (2 Replies)
In the awk below I am trying to add a penalty to a score to each matching $1 in file2 based on the sum of $3+$4 (variable TL) from file1. Then the $4 value in file1 is divided by TL and multiplied by 100 (this valvue is variable S). Finally, $2 in file2 - S gives the updated $2 result in file2.... (2 Replies)
Discussion started by: cmccabe
2 Replies
LEARN ABOUT NETBSD
agr
AGR(4) BSD Kernel Interfaces Manual AGR(4)NAME
agr -- link aggregation pseudo network interface driver
SYNOPSIS
pseudo-device agr
DESCRIPTION
The agr driver provides link aggregation functionality (a.k.a. L2 trunking or bonding).
It supports the IEEE 802.3ad Link Aggregation Control Protocol (LACP) and the Marker Protocol.
The agr driver supports the following link specific flags for ifconfig(8):
link0 Use the round-robin distribution algorithm. Don't use it unless you're really sure, because it violates the frame ordering rule.
-link0 Use the default distribution algorithm, which is based on the hash of DA/SA, TCI, and, if available, some upper layer protocol infor-
mation like ip(4) DA/SA.
link1 Disable LACP. Prevents any LACP or Marker messaging which leaves the ports in the default static configuration. Set this prior to
adding ports.
EXAMPLES
Create an agr interface, agr0, and attach re0 and re1 to it. In other words, aggregate re0 and re1 so that they can be used as a single
interface, agr0. The physical interfaces which are attached to the agr interface must not have any IP addresses, neither IPv4 nor IPv6.
ifconfig re0 inet xxx.xxx.xxx.xxx delete
ifconfig re0 inet6 fe80::xxxx:xxxx:xxxx:xxxx delete
ifconfig re1 inet xxx.xxx.xxx.xxx delete
ifconfig re1 inet6 fe80::xxxx:xxxx:xxxx:xxxx delete
ifconfig agr0 create
ifconfig agr0 agrport re0
ifconfig agr0 agrport re1
Destroy an interface created in the above example.
ifconfig agr0 -agrport re0
ifconfig agr0 -agrport re1
ifconfig agr0 destroy
SEE ALSO ifconfig(8)STANDARDS
IEEE 802.3ad Aggregation of Multiple Link Segments
HISTORY
The agr driver first appeared in NetBSD 4.0.
AUTHORS
The agr driver was written by YAMAMOTO Takashi.
BUGS
There is no way to configure LACP administrative variables, including system and port priorities. The current implementation of the agr
driver always performs active-mode LACP and uses 0x8000 as system and port priorities.
The agr driver uses the MAC address of the first-added physical interface as the MAC address of the agr interface itself. Thus, removing the
physical interface and using it for another purpose can result in non-unique MAC addresses.
The current implementation of the agr driver doesn't prevent unsafe operations like some ioctls against underlying physical interfaces. Such
operations can result in unexpected behaviors, and are strongly discouraged.
There is no way to configure agr interfaces without attaching physical interfaces.
Physical interfaces being added to the agr interface shouldn't have any addresses except for link level address. Otherwise, the attempt will
fail with EBUSY. Note that it includes an automatically assigned IPv6 link-local address.
BSD February 23, 2010 BSD
04-16-2019
.