On AIX 7.1 we have errors with SC_DISK_ERR4 label.
In document "Fibre Channel Planning and Integration: User's Guide and Service Information" I can find SENSE Data description in section "PCI Fibre Channel Adapter, SCSI-3 Protocol (Disk, CD-ROM, Read/Write Optical Device) Error Log Sense Information". But there is no description of value in our case:
We have next Sense Data in our errpt output:
SENSE DATA
So if we check field Status Validity and SCSI Status field, we have next value:
01 - Indicates that the SCSI Status field (SS) is valid
40 - ??? (the value in document is only 02, 08, 18)
Or may be i don't correctly understand this error log sense information.
So, can you give me link for document described Sense Data layout for SC_DISK_ERR4 errors, or may be you can explain how to interpreted this fields
Thank you.
Hello, and good day
I'm somewhat confused with the workings of the Linux operating system, more specifically RedHat 7.1.
The story began a few weeks ago when I downloaded SuSe 7.2, but failed at installation, then Caldera 2.4, then 3.1. Finally I landed upon RedHat 7.1--a fabulous... (6 Replies)
I created two computers with identical hardware, and run the benchmark programs in both starting at the same exact time.
What makes no sense is that the computer that has the lower average index (121) finished the race a good 30 minutes ahead of the computer wich showed the higher avg index... (0 Replies)
I have 3 files in directory mydir named as follows, I run the sequence of commands shown below and I have questions at the result.
File names are:
ABC_GP0
ABC_GP0.ctl
ABC_GPX
Commands and results:
$ ls /mydir/ | grep *
<-- (q1) I get nothing - OK
$ ls /mydir/ | grep... (5 Replies)
I've been referring bash info for processes and came across a structure for a process which is defined like
typedef struct process
{
struct process *next;
char ** argv
.
.
.
}process;
What I don't understand is that in the program there's a for loop which goes like this
job... (2 Replies)
Hi all,
We have below WARNING in /var/adm/messages file from our Solaris server.
WARNING: /sbus@1f,0/SUNW,fas@e,8800000/sd@0,0 (sd0):
Error for Command: write(10) Error Level: Fatal
Requested Block: 16745265 Error Block: 16745269
Vendor: SEAGATE Serial Number:... (8 Replies)
I'm running the following rsync command to sync a directory between the 2 servers:
rsync -az --delete --stats /some_dir/ server_name:/some_dir
I'm getting the following output:
Number of files: 655174
Number of files transferred: 14221
Total file size: 1138531979331 bytes
Total... (0 Replies)
Can someone explain the correlation between how sar names the disk drives and how the rest of the OS names the disk drives?
sar lists my disk drives as sd0, sd1, sd2, etc.....
while format lists my disk drives as c1t0d0, c1t1d0, c1t2d0,etc...
And also why sar shows 8 disks but format... (2 Replies)
Okay so I'm making a simple text based game that branches into different scenarios. By branching I mean branching off into whole different files with that part of the game in it. I got tired of working on scenario 1 so I'm working on scenario 2. As I get started and try to test it, I get an error... (1 Reply)
Discussion started by: lemonoid
1 Replies
LEARN ABOUT DEBIAN
output
OUTPUT(5) File Formats Manual OUTPUT(5)NAME
output - output data file formats
DESCRIPTION
This manual page describes the output formats of the files created by the Yagi-Uda project's output program. The files are ASCII file, so
can be analysed with any graph plotting program.
Example of a .dat File
Below is a typical .dat file, for a 4ele 144-146MHz beam, optimised for a huge (and useless) FB.
# Driven=1 parasitic=3 total-elements=4 design=145.000MHz
# Checked from 144.000MHz to 146.000MHz.
f(MHz) E(deg) H(deg) R jX VSWR Gain(dBi) FB(dB) SideLobes(dB)
144.000 54.7 71.5 44.47 -2.35 1.136 9.386 21.944 16.650
144.500 54.0 70.1 41.34 -0.75 1.210 9.553 27.244 17.153
145.000 53.2 68.4 37.55 1.61 1.335 9.742 103.055 17.777
145.500 52.3 66.6 33.26 5.00 1.530 9.947 25.734 18.547
146.000 51.3 64.6 28.77 9.63 1.832 10.149 18.919 18.919
What is what in the .dat file
The f(MHz) column is the frequency (MHz) at which the data is evaluated at.
The E(deg) column is the approximate 3dB E-plane bandwidth calculated to the nearest 0.1 degree.
The H(deg) column is the approximate 3dB H-plane bandwidth calculated to the nearest 0.1 degree.
The (R) column is the input resistance in Ohms.
The (jX) column is the input reactance in Ohms.
The (VSWR) column is the input VSWR, usually refered to a 50 Ohm input, but this may be changed.
The Gain (dBi) column is the gain at theta=90 degrees, which is the forward direction of the beam. It is possible that a higher gain occurs
at other than 90 degrees, but this is not taken into account. The antenna is seriously at fault if this occurs.
The FB(dB) column is the front to back ratio in dB.
The Sidelobes(dB) column is the minimum level in dB down from the peak gain of any sidelobe. This is not calculated unless the '-c' option
is used, and then only on some optimisation techniques.
Example of a .gai File
The following is a small section of the .gai file.
f(MHz) theta gain-E(dBi) G(E)-peak phi gain-H(dBi) G(H)-peak
144.0000 -90.0000-12.5584-21.9444 -180.0000 -12.5584-21.9444
144.0000 -45.0000-7.3507-16.7367 -135.0000 -3.5971-12.9830
144.0000 0.0000 -999.0000 -1008.3860 -90.0000-0.9010-10.2870
144.0000 45.0000 0.1848 -9.2012-45.0000 4.0261 -5.3599
144.0000 90.0000 9.3860 0.0000 0.0000 9.3860 0.0000
144.0000 135.0000 0.1848 -9.2012 45.0000 4.0261 -5.3599
144.0000 180.0000 -999.0000 -1008.3860 90.0000 -0.9010-10.2870
144.0000 225.0000 -7.3507-16.7367 135.0000 -3.5971-12.9830
144.0000 270.0000 -12.5584-21.9444 180.0000 -12.5584-21.9444
What is what in the .gai file
The f(MHz) column is the frequency in MHz.
The theta column is the angle theta, for which the next two columns refer.
The gain-E(dBi) is the gain at theta, relative to an isotropic radiator. This is the E-plane gain. Hence at the peak (theta), this gives
the peak forward gain.
The G(E)-peak is the gain at theta, relative to the peak gain. Hence at the peak (theta=90 degrees), this is zero.
The phi column has nothing to do with the previous 3 columns. It is the angle for which the next two columns refer.
The gain-H(dBi) is the gain at phi, relative to an isotropic radiator. This is the H-plane gain. Hence at the peak (phi=0), this gives the
peak forward gain.
The G(H)-peak is the gain at phi, relative to the peak gain. Hence at the peak (phi=0 degrees), this is zero.
Example of a .up File
The .up file list the improvements made by optimise to an antenna design. Starting from the original design, the file is appended each time
a new better design is found. Here is an example, where the final line is the performance of the 4ele beam with the .dat file shown ear-
lier.
1 7.57dBi, 16.93dB F/B, Z=(31.77-56.34j) Ohms, VSWR=3.95, SL=16.95 dB
84 7.58dBi, 16.93dB F/B, Z=(31.78-56.32j) Ohms, VSWR=3.95, SL=16.95 dB
623 7.58dBi, 16.93dB F/B, Z=(31.78-56.28j) Ohms, VSWR=3.95, SL=16.95 dB
89345 9.74dBi, 103.06dB F/B, Z=(37.55 +1.61j) Ohms, VSWR=1.33, SL=17.78 dB
What is what in the .up file
The first column is an integer specifying the iteration. The other columns, going from left to right are gain(dBi), FB, input impedance,
VSWR and level of the most significant sidelobe, in dB down on the peak gain.
SEE ALS0yagi(1), output(1), input(1), optimise(1), first(1) and yagi(5).
AUTHORS
Dr. David Kirkby G8WRB (david.kirkby@onetel.net), with help with converting to DOS from Dr. Joe Mack NA3T (mack@fcrfv2.ncifcrf.gov).
Version 1.16 24th October 2000 OUTPUT(5)