I'm new with UNIX, i have a pseries server from IBM and i need to install AIX 4.3, i never used wyse terminal or AIX, i need help to know how to install it, i have the server and the wyse i get in into the aixterm, over com1 but i don't know wich command use or what to do to install it..... ... (0 Replies)
Hi All --
I have an old 7028-6C1 which I'm using to learn AIX. The system didn't include a graphics card, so I connected via the serial port and performed a fresh install of AIX 5L V5.3.
Later, I purchased a GXT135P (2849) graphics card, and added it to the system. When I ran diag, I was able... (2 Replies)
Hello Gurus,
i'm quite new person in AIX world, actually i'm SAP consultant. But due to my job faced with AIX.
Trying to configure new server for installation SAP. We have 4 disks one of them (hdisk3) has VG rootvg. How i can extend rootvg with another disk?
i tried:
# extendvg rootvg hdisk0... (2 Replies)
Anyone can help me answer the question.
Why does they use Linux on IBM pSeries not AIX.
I can't understand why, cause AIX is the best supporting from IBM pSeries.
Tks you. (3 Replies)
Hi ,
I am planing to buy IBM pSeries Power5 9111-285 1,9 GHz but I am confused with few things. I would be happy if you could clear it up for me ?
1.Do I have to buy some license in order to create Lpars ?
2.Do I have to buy some license in order to use HMC , micro - partiocioning , VIOS... (4 Replies)
Hello,
I installed PowerVM IVM Virtual I/O on P-550 but later found out that the machine isn't activated for CoD VET code for virtualization.
So when booted , it goes into OPEN Firmware
I/O Hosting requires a hosting partition boot not permitted exit called
> ok
Panel shows > IO... (3 Replies)
Hidey Ho Folks,
Looking to buy a pServer for playing around with the IBM side of things. Looked around for a bit and notice that there is a significant price gap for the used 570's (Single Units) vs the 520's and 550's that folks are selling. Curious what to watch out for in either case? And... (6 Replies)
Hello,
I'm very rookie to AIX and attempting to install AIX. I have vio ready on the machine and don't know how to install OS? Inserted Volume 1 DVD into the ROM, don't know what to do next. Searched many forum but cant find the this basic thing. Please let me know how to install AIX on this... (4 Replies)
Hi There,
I have zero information and zero knowledge for IBM virtual machine except Amazon cloud and VMware ESXi (Only Linux OS available).
Anyone could provide me the following answer -
Can IBM VM been deploy on X86 and X64 (Intel Chip)?
If answer is yes any chance to deploy AIX OS... (13 Replies)
Discussion started by: chenyung
13 Replies
LEARN ABOUT OSF1
sys_attrs_bparm
sys_attrs_bparm(5) File Formats Manual sys_attrs_bparm(5)NAME
sys_attrs_bparm - bparm subsystem attributes
DESCRIPTION
This reference page lists and describes attributes for the Boot Parameters (bparm) kernel subsystem. Refer to the sys_attrs(5) reference
page for an introduction to the topic of kernel subsystem attributes.
Identifies the device from which the system was last booted. This attribute corresponds to the console firmware environment vari-
able with the same name. Do not modify this value, which is set when the system boots.
A combination of flags that controls the boot loader and kernel. This attribute corresponds to the console firmware environment
variable with the same name. Values for the variable are: Boot to multiuser mode. By default, the kernel boots to single-user mode.
Enable the kdebug debugger to debug the kernel. By default, kdebug is not enabled in the kernel. Produce full dumps when the system
crashes. By default, partial dumps are produced. Prompt for an alternate kernel and special arguments when the system is booted. By
default, no questions are asked.
Set boot_osflags only at the console prompt or by using the consvar utility.
Identifies the boot device to be used when one is not included in the boot command line. This attribute corresponds to the console
firmware environment variable with the same name. Set bootdef_dev only at the console prompt or by using the consvar utility.
SEE ALSO
Commands: consvar(8)
Others: sys_attrs(5)
System Administration
sys_attrs_bparm(5)