03-10-2019
Well if you find the exact same hard disk, and find any means to plug it onto your T70 you may use the dd utility to make an exact copy ... it works also if the disk is bigger only you loose the difference...
This User Gave Thanks to vbe For This Post:
8 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
HI ALL,
I need to backup HDD with SCO UNIX. I need to have a full functionaly backup of this hard disk. Does anybody have any tool or subsription how to do it. I tried some SW, but after when I tried to use this copy of my original disk "can not find a root directory". Thanks in advance. (1 Reply)
Discussion started by: jardas
1 Replies
2. SCO
Hi guys,
I have this quick question , is it posible to isntall SCO 5.0.7 on a serial ATA and if it is can you tell me how or maybe a website that has some info about this.
I'm not using any raid, just one HDD.
Thanks a lot (0 Replies)
Discussion started by: josramon
0 Replies
3. UNIX for Advanced & Expert Users
Hello,
I have a P4, 2.4GHz, 256MB ASROCK mainboard: I am trying to install sco 5.0.5 on an 80gb hdd IDE .
I have tried the following techniques:
1. using the updated wd btld image- no success
2. defbootstr biosgeom
3. use interactive divvy, make adjustments using dkinit/dparam during... (0 Replies)
Discussion started by: pude
0 Replies
4. SCO
Hi guys,
I have this problem ,
One of our client's hdd went down and we cannot boot up the machine , I've installed a new hdd with a fresh copy of SCO 5.0.6 same as the one in the old HDD, i think the data still good in the old HDD.
My question!!!
How can i access the data from the fresh... (4 Replies)
Discussion started by: josramon
4 Replies
5. Ubuntu
Hi guys, I am total newbie to Linux / Ubuntu but trying it to solve the problem I have.
I have an OKI printer with bad HDD and trying to clone one from the same HDD from working printer. Board it goes on has a Fiery chipset and system used is Linux based / related - to the best of my knowlege. I... (12 Replies)
Discussion started by: Unlimitedbt
12 Replies
6. HP-UX
Hi there,
I got a pretty old HP 382 workstation, and the hdd is pretty LOUD ... ;)
So I thought I clone it to an much quiter one.
I tried this:
- removed the loud hdd
- connected it to an system running knoppix 7.0.4 (hdd is recognized with UFS filesystem; Clonezilla couldn't handle the... (9 Replies)
Discussion started by: pelegrine
9 Replies
7. SCO
Hi all
I have read about mounting crashed HDD from a sco system in this forum. However this I received an image on raw format of the crashed system that was using an IDE HDD. Which method should I mount my image? IDE scsi or USB? The image is stores in an external connected through USB .
Also... (4 Replies)
Discussion started by: OrangeKenny
4 Replies
8. AIX
Hi Folks,
I am facing an issue with the performance.
P4 with 1 processor and 16 GB RAM and SAN HDD = Oracle report takes 25 minutes
P5 with 2 processors and 16 GB RAM internall HDD with LPAR = Oracle Report takes 1 hour 15 minutes ( please note I have assigned all the max processors and... (7 Replies)
Discussion started by: filosophizer
7 Replies
LEARN ABOUT OSF1
disklabel
disklabel(4) Kernel Interfaces Manual disklabel(4)
NAME
disklabel - Disk pack label
SYNOPSIS
#include <sys/disklabel.h>
DESCRIPTION
Each disk or disk pack on a system may contain a disk label which provides detailed information about the geometry of the disk and the par-
titions into which the disk is divided. It should be initialized when the disk is formatted, and may be changed later with the disklabel
program. This information is used by the system disk driver and by the bootstrap program to determine how to program the drive and where
to find the file systems on the disk partitions. Additional information is used by the file system in order to use the disk most effi-
ciently and to locate important file system information. The description of each partition contains an identifier for the partition type
(standard file system, swap area, etc.). The file system updates the in-core copy of the label if it contains incomplete information about
the file system.
The label is located in sector number LABELSECTOR of the drive, usually sector 0 (zero) where it may be found without any information about
the disk geometry. It is at an offset LABELOFFSET from the beginning of the sector, to allow room for the initial bootstrap. The disk
sector containing the label is normally made read-only so that it is not accidentally overwritten by pack-to-pack copies or swap opera-
tions; the DIOCWLABEL ioctl, which is done as needed by the disklabel program, allows modification of the label sector.
A copy of the in-core label for a disk can be obtained with the DIOCGDINFO ioctl; this works with a file descriptor for a block or charac-
ter (raw) device for any partition of the disk. The in-core copy of the label is set by the DIOCSDINFO ioctl. The offset of a partition
cannot generally be changed, nor made smaller while it is open. One exception is that any change is allowed if no label was found on the
disk, and the driver was able to construct only a skeletal label without partition information. Finally, the DIOCWDINFO ioctl operation
sets the in-core label and then updates the on-disk label; there must be an existing label on the disk for this operation to succeed.
Thus, the initial label for a disk or disk pack must be installed by writing to the raw disk. All of these operations are normally done
using the disklabel program.
RELATED INFORMATION
Files: disktab(4)
Commands: disklabel(8) delim off
disklabel(4)