03-10-2019
Quote:
Originally Posted by
Phat
So strange we can see only 1 WWPN. Or only this WWPN is used?
I suspect it uses the zoning with type active-standby
Yes, i would suspect the zoning too. You should investigate with the storage guy, especially if he has zoned
both of the WWPNs on
both of the virtual adapters. They often think that - one cable one WWPN - one of them is enough.
Only one of the two WWPNs is used - at a time. The second is needed for LPM: while the one WWPN is still used on the source system the second one is used on the target system and once the LPM move is complete the original WWPN is not used any more until you initiate another LPM move.
bakunin
9 More Discussions You Might Find Interesting
1. AIX
Want to configure IBM raid strorage but the aix 5L cds do not have the drivers for the fibre channels. The machine is RS/6000. I have gone to IBM downlaodable sites but i can't find the drivers? help pliz:mad: (4 Replies)
Discussion started by: Zim-Aix-Guru
4 Replies
2. AIX
Hello,
I have two systems that are being prepared to be SAN attached ..
can anyone tell me any specific checks I should perform prior to the cards being installed...
I am aware of firmware / OS level and relevant drivers, is there anything else?
thanks
Chris. (8 Replies)
Discussion started by: chlawren
8 Replies
3. AIX
Hello,
Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter.
It is similar to virtual scsi adapter.
In my client partition I created the virtual Fibre Adapter mapped it with the VIO... (1 Reply)
Discussion started by: filosophizer
1 Replies
4. Solaris
Hi ,
I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Discussion started by: naveen448
0 Replies
5. AIX
hi
i have two aix servers and I was asked to setup a secure shell between the two servers using the sybase user. Can any one let me know how to do this (2 Replies)
Discussion started by: newtoaixos
2 Replies
6. Hardware
We will be buying new Xeon E5-based servers for our datacenter and were wondering which Fibre Channel host bus adapters we should select for these. The choices are Emulex or QLogic (8Gb FC HBAs). Anybody have any recommendations on which is the better choice?
Thanks in advance. (1 Reply)
Discussion started by: atahmass
1 Replies
7. AIX
Hello,
Just a quick question
Usually from a PSERIES if you want to connect to IBM SAN Storage
you connect the IBM SAN Storage through a SAN Switch
something like this
---
however my question
Can you connect
from Pseries directly to San Storage without SAN Switch
what would be... (8 Replies)
Discussion started by: filosophizer
8 Replies
8. Solaris
Hi
I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10.
After power on the system stops at ok prompt, them I issued the following commands:
{0} ok setenv auto-boot? false
auto-boot? = false
{0} ok reset-all
SPARC T3-1B,... (10 Replies)
Discussion started by: fretagi
10 Replies
9. Solaris
Hi,
One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too.
There are two disks of 72GB, both are mirrored in SVM. It complains about... (5 Replies)
Discussion started by: solaris_1977
5 Replies
LEARN ABOUT DEBIAN
smp_zone_activate
SMP_ZONE_ACTIVATE(8) SMP_UTILS SMP_ZONE_ACTIVATE(8)
NAME
smp_zone_activate - invoke ZONE ACTIVATE SMP function
SYNOPSIS
smp_zone_activate [--expected=EX] [--help] [--hex] [--interface=PARAMS] [--raw] [--sa=SAS_ADDR] [--verbose] [--version] SMP_DEVICE[,N]
DESCRIPTION
Sends a SAS Management Protocol (SMP) ZONE ACTIVATE function request to a SMP target. The SMP target is identified by the SMP_DEVICE and
the --sa=SAS_ADDR. Depending on the interface, the SAS_ADDR may be deduced from the SMP_DEVICE. The mpt interface uses SMP_DEVICE to iden-
tify a HBA (an SMP initiator) and needs the additional ,N to differentiate between HBAs if there are multiple present.
This function, if successful, will cause various zoning related shadow values (e.g. zone permission table and zone phy information) to be
copied to the corresponding current values. If the saving to "saved" values option has been selected then the various zoning related shadow
values will also be copied to the corresponding saved values.
OPTIONS
Mandatory arguments to long options are mandatory for short options as well.
-E, --expected=EX
set the 'expected expander change count' field in the SMP request. The value EX is from 0 to 65535 inclusive with 0 being the
default value. When EX is greater than zero then if the value doesn't match the expander change count of the SMP target (i.e. the
expander) when the request arrives then the target ignores the request and sets a function result of "invalid expander change count"
in the response.
-h, --help
output the usage message then exit.
-H, --hex
output the response (less the CRC field) in hexadecimal.
-I, --interface=PARAMS
interface specific parameters. In this case "interface" refers to the path through the operating system to the SMP initiator. See
the smp_utils man page for more information.
-r, --raw
send the response (less the CRC field) to stdout in binary. All error messages are sent to stderr.
-s, --sa=SAS_ADDR
specifies the SAS address of the SMP target device. The mpt interface needs this option and it will typically be an expander's SAS
address. The SAS_ADDR is in decimal but most SAS addresses are shown in hexadecimal. To give a number in hexadecimal either prefix
it with '0x' or put a trailing 'h' on it.
-v, --verbose
increase the verbosity of the output. Can be used multiple times.
-V, --version
print the version string and then exit.
CONFORMING TO
The SMP ZONE ACTIVATE function was introduced in SAS-2 .
AUTHORS
Written by Douglas Gilbert.
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright (C) 2011 Douglas Gilbert
This software is distributed under a FreeBSD license. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-
POSE.
SEE ALSO
smp_utils, smp_zone_lock, smp_zone_unlock, smp_ena_dis_zoning(smp_utils)
smp_utils-0.96 June 2011 SMP_ZONE_ACTIVATE(8)