Want to configure IBM raid strorage but the aix 5L cds do not have the drivers for the fibre channels. The machine is RS/6000. I have gone to IBM downlaodable sites but i can't find the drivers? help pliz:mad: (4 Replies)
Hello,
I have two systems that are being prepared to be SAN attached ..
can anyone tell me any specific checks I should perform prior to the cards being installed...
I am aware of firmware / OS level and relevant drivers, is there anything else?
thanks
Chris. (8 Replies)
Hello,
Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter.
It is similar to virtual scsi adapter.
In my client partition I created the virtual Fibre Adapter mapped it with the VIO... (1 Reply)
Hi ,
I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
hi
i have two aix servers and I was asked to setup a secure shell between the two servers using the sybase user. Can any one let me know how to do this (2 Replies)
We will be buying new Xeon E5-based servers for our datacenter and were wondering which Fibre Channel host bus adapters we should select for these. The choices are Emulex or QLogic (8Gb FC HBAs). Anybody have any recommendations on which is the better choice?
Thanks in advance. (1 Reply)
Hello,
Just a quick question
Usually from a PSERIES if you want to connect to IBM SAN Storage
you connect the IBM SAN Storage through a SAN Switch
something like this
---
however my question
Can you connect
from Pseries directly to San Storage without SAN Switch
what would be... (8 Replies)
Hi
I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10.
After power on the system stops at ok prompt, them I issued the following commands:
{0} ok setenv auto-boot? false
auto-boot? = false
{0} ok reset-all
SPARC T3-1B,... (10 Replies)
Hi,
One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too.
There are two disks of 72GB, both are mirrored in SVM. It complains about... (5 Replies)
Discussion started by: solaris_1977
5 Replies
LEARN ABOUT HPUX
gvid_no_claim_dev
gvid_no_claim_dev(5) File Formats Manual gvid_no_claim_dev(5)NAME
gvid_no_claim_dev - PCI Vendor/Device ID that the gvid graphics driver will not claim
VALUES
Failsafe
Default
Allowed values
Recommended values
Specific to the device you wish to prevent from claiming.
DESCRIPTION
This tunable specifies the PCI Vendor ID and/or Device ID of a graphics device that the HP graphics driver should not claim.
The graphics driver was designed to be a general purpose driver for all PCI graphics cards. As a result, the driver will attempt to claim
any PCI graphics display device found on the system. This can be a problem for graphics device developers who need their own graphics
driver to claim their own graphics device.
The value of will specify a PCI Vendor ID and/or Device ID of a graphics card that the gvid graphics driver should not claim. It is a 32
bit number, with the upper 16 bits containing the PCI Vendor ID and the lower 16 bits containing the PCI Device ID. Either the Vendor ID
or Device ID can use a wildcard value of
For example, if is set to the value the driver will ignore graphics devices with a PCI Vendor ID of and a Device ID of If is set to the
driver will not claim any graphics cards with a Vendor ID of regardless of the Device ID.
Who Is Expected to Change This Tunable?
Anyone who wishes the graphics driver to ignore a specific graphics device. This will typically be someone writing their own graphics
driver for their own hardware.
Restrictions on Changing
Changes to this tunable take effect at the next reboot.
What Other Tunables Should Be Changed at the Same Time?
None.
WARNINGS
All HP-UX kernel tunable parameters are release specific. This parameter may be removed or have its meaning changed in future releases of
HP-UX.
Installation of optional kernel software, from HP or other vendors, may cause changes to tunable parameter values. After installation,
some tunable parameters may no longer be at the default or recommended values. For information about the effects of installation on tun-
able values, consult the documentation for the kernel software being installed. For information about optional kernel software that was
factory installed on your system, see at
AUTHOR
was developed by HP.
Tunable Kernel Parameters gvid_no_claim_dev(5)
03-08-2019
you want to emphasize full details are very crucial???