Can you explain to me 1 thing. As you mentioned, each physical/virtual FC has 2 WWPN. As I check on HMC, I can see the virtual FC assigned to my LPAR has 2 WWPN as screenshot attached.
Want to configure IBM raid strorage but the aix 5L cds do not have the drivers for the fibre channels. The machine is RS/6000. I have gone to IBM downlaodable sites but i can't find the drivers? help pliz:mad: (4 Replies)
Hello,
I have two systems that are being prepared to be SAN attached ..
can anyone tell me any specific checks I should perform prior to the cards being installed...
I am aware of firmware / OS level and relevant drivers, is there anything else?
thanks
Chris. (8 Replies)
Hello,
Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter.
It is similar to virtual scsi adapter.
In my client partition I created the virtual Fibre Adapter mapped it with the VIO... (1 Reply)
Hi ,
I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
hi
i have two aix servers and I was asked to setup a secure shell between the two servers using the sybase user. Can any one let me know how to do this (2 Replies)
We will be buying new Xeon E5-based servers for our datacenter and were wondering which Fibre Channel host bus adapters we should select for these. The choices are Emulex or QLogic (8Gb FC HBAs). Anybody have any recommendations on which is the better choice?
Thanks in advance. (1 Reply)
Hello,
Just a quick question
Usually from a PSERIES if you want to connect to IBM SAN Storage
you connect the IBM SAN Storage through a SAN Switch
something like this
---
however my question
Can you connect
from Pseries directly to San Storage without SAN Switch
what would be... (8 Replies)
Hi
I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10.
After power on the system stops at ok prompt, them I issued the following commands:
{0} ok setenv auto-boot? false
auto-boot? = false
{0} ok reset-all
SPARC T3-1B,... (10 Replies)
Hi,
One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too.
There are two disks of 72GB, both are mirrored in SVM. It complains about... (5 Replies)
Discussion started by: solaris_1977
5 Replies
LEARN ABOUT FREEBSD
hv_netvsc
HYPER-V(4) BSD Kernel Interfaces Manual HYPER-V(4)NAME
hv_netvsc -- Hyper-V Network Virtual Service Consumer
SYNOPSIS
To compile this driver into the kernel, place the following lines in the system kernel configuration file:
device hyperv
DESCRIPTION
The hv_netvsc driver implements the virtual network device for FreeBSD guest partitions running on Hyper-V. FreeBSD guest partitions running
on Hyper-V do not have direct access to network devices attached to the Hyper-V server. Although a FreeBSD guest can access network devices
using Hyper-V's full emulation mode, the performance in this mode tends to be unsatisfactory.
To counter the above issues, the hv_netvsc driver implements a network Virtual Service Consumer (VSC) that relays network requests from the
guest partition to the network Virtual Service Provider (VSP) hosted in the root partition using the high performance data exchange infra-
structure provided by hv_vmbus(4) driver. The VSP in the root partition then forwards the network related requests to the physical network
card.
SEE ALSO hv_ata_pci_disengage(4), hv_storvsc(4), hv_utils(4), hv_vmbus(4)HISTORY
Support for hv_netvsc first appeared in FreeBSD 10.0. The driver was developed through a joint effort between Citrix Incorporated, Microsoft
Corporation, and Network Appliance Incorporated.
AUTHORS
FreeBSD support for hv_netvsc was first added by Microsoft BSD Integration Services Team <bsdic@microsoft.com>.
BSD September 10, 2013 BSD