[ASK] - AIX Fibre Channel behavior Post: 303031938

9 More Discussions You Might Find Interesting

1. AIX

Fibre channel drivers on RS/6000 aix 5L

Want to configure IBM raid strorage but the aix 5L cds do not have the drivers for the fibre channels. The machine is RS/6000. I have gone to IBM downlaodable sites but i can't find the drivers? help pliz:mad:

2. AIX

Install Fibre Card AIX 5.3

Hello, I have two systems that are being prepared to be SAN attached .. can anyone tell me any specific checks I should perform prior to the cards being installed... I am aware of firmware / OS level and relevant drivers, is there anything else? thanks Chris.

3. AIX

Power6 Virtual Fibre Channel Adapter

Hello, Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter. It is similar to virtual scsi adapter. In my client partition I created the virtual Fibre Adapter mapped it with the VIO...

4. Solaris

USCSICMD ioctl calls for Fibre Channel(FC) devices on Solaris 10?

Hi , I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error...

5. AIX

Setting up a secure channel with AIX

hi i have two aix servers and I was asked to setup a secure shell between the two servers using the sybase user. Can any one let me know how to do this

6. Hardware

Fibre Channel HBA recommendations?

We will be buying new Xeon E5-based servers for our datacenter and were wondering which Fibre Channel host bus adapters we should select for these. The choices are Emulex or QLogic (8Gb FC HBAs). Anybody have any recommendations on which is the better choice? Thanks in advance.

7. AIX

AIX - Fibre Adapter and IBM Storage

Hello, Just a quick question Usually from a PSERIES if you want to connect to IBM SAN Storage you connect the IBM SAN Storage through a SAN Switch something like this --- however my question Can you connect from Pseries directly to San Storage without SAN Switch what would be...

8. Solaris

Fibre channel link down on booting Solaris server

Hi I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10. After power on the system stops at ok prompt, them I issued the following commands: {0} ok setenv auto-boot? false auto-boot? = false {0} ok reset-all SPARC T3-1B,...

9. Solaris

Fibre Channel link not ready on Netra 240

Hi, One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too. There are two disks of 72GB, both are mirrored in SVM. It complains about...

LEARN ABOUT CENTOS

sg_rdac

SG_RDAC(8)							     SG3_UTILS								SG_RDAC(8)

NAME

       sg_rdac - display or modify SCSI RDAC Redundant Controller mode page

SYNOPSIS

       sg_rdac [-a] [-f=LUN] [-v] [-V] DEVICE

DESCRIPTION

       sg_rdac	displays  or  modifies	the RDAC controller settings via the Redundant Controller mode page (0x2C). When modifying the settings it
       allows to transfer the ownership of individual drives to the controller the command was received on.

OPTIONS

       -a     Transfer all (visible) devices

       -f=LUN Transfer the device identified by LUN. This command will only work if the controller supports 'Dual Active Mode' (aka  active/active
	      mode).

       -v     be verbose

       -V     print version string then exit

EXIT STATUS

       The exit status of sg_rdac is 0 when it is successful. Otherwise see the sg3_utils(8) man page.

AUTHOR

       Written by Hannes Reinecke <hare at suse dot com>, based on sg_emc_trespass.

REPORTING BUGS

       Report bugs to <dgilbert at interlog dot com>.

COPYRIGHT

       Copyright (C) 2006-2012 Hannes Reinecke, Douglas Gilbert.
       This  software  is distributed under the GPL version 2. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-
       POSE.

sg3_utils-1.35							   November 2012							SG_RDAC(8)