Currently I have a box that I am dual-booting Win98 & Linux on. I have an unformatted 3 gig slice that I would like to install Soloris 8 x86 on. Are there any issues I should be aware of? How close is the x86 install to the sparc install? The Linux partition will be going away but I need to reatain... (1 Reply)
I've been asking on IRC channels but no one answers me, I need to format my hard drive, normally it's just format c:
but c doesn't exist, how do I format when I have linux mandrake installed. Please reply to this quickly, I'm kinda in a rush :( (1 Reply)
Hi Again Guys ,
Please i installed linux RH 6.1 on Toshiba , 10G , RAM=128 , 600 MHZ .
After i installed linux i got many error messages , seems it was not installed correctly , also when i finished installation it did not ask me for the 2nd installation CD , and when i logged as root , i... (5 Replies)
OK, I have a command that is getting a result, that I am trying to format using awk.
I think it's pretty ugly, and there is probably a better way to do it, but this is sorta working for me. Anyway, the command:
cat /var/log/cups/page_log | grep testuser | grep My_office_printer | awk '{gsub... (5 Replies)
I need to ask a question on how to format the output in a csv format. Right now i am running a shell script which executes a command and the following output is append through a unix script in a .csv file.
So the output of xyz.csv is as follow :-
1. Number = 25 Amount $84,132.22
2.... (1 Reply)
I have file with different columns
for ex.
contents of file "txt"
NAME AGE MARKS
HARRY 23 89
TOM 12 67
BOB 23 11
and you see its not formatted.Now, I need the file "txt" to be formatted like
COLUMN1 COLUMN2 COLUMN3
NAME AGE ... (3 Replies)
I have the following nmap file output with the multiple IP’s listed in the format below. Is there a way that GREP can format the output to just display IP and any ports that contain 'http' for that IP on its own line?
file:
Host: 192.168.1.xxx () Ports: 80/open/tcp//http///,... (3 Replies)
Discussion started by: FCoda10
3 Replies
LEARN ABOUT REDHAT
sd
SD(4) Linux Programmer's Manual SD(4)NAME
sd - Driver for SCSI Disk Drives
SYNOPSIS
#include <linux/hdreg.h> /* for HDIO_GETGEO */ #include <linux/fs.h> /* for BLKGETSIZE and BLKRRPART */
CONFIG
The block device name has the following form: sdlp, where l is a letter denoting the physical drive, and p is a number denoting the parti-
tion on that physical drive. Often, the partition number, p, will be left off when the device corresponds to the whole drive.
SCSI disks have a major device number of 8, and a minor device number of the form (16 * drive_number) + partition_number, where drive_num-
ber is the number of the physical drive in order of detection, and partition_number is as follows:
partition 0 is the whole drive
partitions 1-4 are the DOS "primary" partitions
partitions 5-8 are the DOS "extended" (or "logical") partitions
For example, /dev/sda will have major 8, minor 0, and will refer to all of the first SCSI drive in the system; and /dev/sdb3 will have
major 8, minor 19, and will refer to the third DOS "primary" partition on the second SCSI drive in the system.
At this time, only block devices are provided. Raw devices have not yet been implemented.
DESCRIPTION
The following ioctls are provided:
HDIO_GETGEO
Returns the BIOS disk parameters in the following structure:
struct hd_geometry {
unsigned char heads;
unsigned char sectors;
unsigned short cylinders;
unsigned long start;
};
A pointer to this structure is passed as the ioctl(2) parameter.
The information returned in the parameter is the disk geometry of the drive as understood by DOS! This geometry is not the physical
geometry of the drive. It is used when constructing the drive's partition table, however, and is needed for convenient operation of
fdisk(1), efdisk(1), and lilo(1). If the geometry information is not available, zero will be returned for all of the parameters.
BLKGETSIZE
Returns the device size in sectors. The ioctl(2) parameter should be a pointer to a long.
BLKRRPART
Forces a re-read of the SCSI disk partition tables. No parameter is needed.
The scsi(4) ioctls are also supported. If the ioctl(2) parameter is required, and it is NULL, then ioctl() will return -EINVAL.
FILES
/dev/sd[a-h]: the whole device
/dev/sd[a-h][0-8]: individual block partitions
SEE ALSO scsi(4)
1992-12-17 SD(4)